Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hi, is there a way to configure ACE to perform rate liimting per source address? Say if a source sends more than 100 connections per second, I want ACE to drop further connections from this perticular source only.thanks.
Hello Everyone,I have a requirement to select a farm based on source IP address. I tried creating a match all class-map that matches on the virtual-address and source address but I get this message.LB01/Admin(config-cmap)# match source-address x.x.x...
Hi All,Have anyone try the following:Can I implement 2 WAE (router w/SRE) at 2 locations (data center and branch) without an dedicated WAE acting as central manager. Will this work. ? Your help is appreciate. Thanks in advance.Jas
Hi, I have CSS in single arm deployment model. I want to do the load balance following URL.http://irs.abc.com/irs.htm I have configure the following stepsservice IRC_1 ip address 192.168.17.12 keepalive type tcp keepalive port 80 active servi...
Good afternoonI´m having a problem/issue with my CSM. I have a WS-X6066-SLB-APC - Version 4.2(1), installed on a 6500, and for a while now whenever I ping the VIPs (vservers) I detect some packet loss (In 10.000 ping packets, I loose around 1%), and ...
Hi All,I have a L7 policy-map to filter by URI, only the websites listed in the "class-map type http" are allowed. The next step is to monitor which connections were dropped because a wrong host value in the header host field of HTTP packet was recei...
Hi.I'm having an issue with getting a HTTP probe to do a content check on a Sharepoint 2010 front end.I have the following probe configured:probe http TCP-HTTP-Status-Check description "Test HTTP request to Portal Page" interval 5 passdetect inter...
Hi all,I need to be able to send and netflow from our's WAE using UDP port 9995.I this posible, if not in what version will it be? Regards Jan Rockstedt
Hi, can ACE Load Balancer teminate client connection with a customized html message (eg: server is offline for maintenance) when 2 rserver are down or probe is failing? Assuming there are 2 rserver defined in a serverfarm with a probe configured for ...
Hi ,We are seeing intrface errors on the gi 1/0 port of a WAVE-7371. We changed the cables but it didnot help. The switch interface conected to the WAE looks good and no errors are found on it. port settings are same on both the sidesThe mangement po...
Hi ,I need to De-register a WAE which is not being used anymore,as the device is offline I cannot deregister it using CLI. If I need to deregister it from WAAS CM using central manger do I need to delete the device by clicking on the manage device t...
Hi guys, I've seen the examples in previous posts and some others online including the cisco documentation.I find my scenario a bit different though and have not been able to implement a redirect that works for me.In DNS i have domainx.com pointing t...
ACE 4710 TACACS issues ,How to setup user with Admin context access permission . I have enable the TACACS and it can directly put me in Context mode not in Admin Context mode .
Hi there,I'm currently in the process of migrating from CSS to CSM and I have a question regarding TCP state tracking between two CSM's. In the documentation it says the the connection information is sent over to the secondary CSM using a multicast...
Hello,I have a question regarding CSS loadbalancer. Let's say there are 2 vlans in CSS:1. Vlan 10: 10.1.1.0/24 as external interface, interface where most of the clients are coming from. 2. Vlan 20: 10.1.2.0/24 for real server vlan.Virtual IP 10.1.1....
