Hi all, I can't make IOS XRv 6.0.0 (and older ones like 5.3) to boot in vmware. I have tried to import the ova to: - VMware workstation 10 (on two different PCs vtx/vtd enabled) - VMware ESXi5.5 (on server hardware) - Oracle VirtualPC All the above...
Forum Posts
I have access to CML at work and I've built a couple simulations. I would like to have the ability to simulate actual network traffic. I have a small network simulation setup with two managed servers on two separate networks. I have my network set...
Hi, We're running CML version 1.3.286.04 and one of the users is trying to enable the anyconnect VPN in the ASAv and he's seeing a licensing error. Does anyone know if this feature should be available? Sorry or the poor image, it's all he sent. ...
Two problems with 'extract configuration changes' 1) Simulation/Extract configurations fails on one node with message... (See end for the console log) Extract configurations for simulation My_Topologies@INETBase1-AeQ0jo encountered an unexpected ex...
we bought 15 nodes corporate CML. But the only single user can run 15 nodes. if other users try to run his own lab with 10-14 nodes. it says your 15 nodes already running in another project. whats the point of buying corporate version then.
dear All i face one of IT PEOPLES they need to see forwarding rate, in Cisco 2960+24TC-L switch on Cisco datasheet its available and can be seen the people need to see based on Cisco command on enable mode or global mode? i search many commands b...
Hi, Last year I pass my CCNA exam and now I start to study for CCNP. I'm 60 year old but feel much younger. I just received my first new (old) LAB and I have 1 x Catalist 2950 (cable no.1) 1 x Catalist 3550 (cable no.2) 2 x Catalist 3560 Poe 24 (cab...
Hi, I try to create an enviroment to practice,. This scenario is the following. One DHCP SERVER directly connect to a router with addres 172.20.100.10/24 This router is directly connect to a SW with addres 172.20.250.2/24 (this is my default vlan 1) ...
Resolved! Modeling Lab from existing configs
I've searched around, and I don't seem to be able to find the answer. Is there software that ships with modeling lab (or is available for download) that will take a folder of Cisco existing configurations and create the topology and configs for the l...
I cannot using GUI method I use CiscO Switch SG300-10P model I was connect Switch and System Using Straight thought cable.I can ping using CMD. But I can't access the Browser method. I used "192.168.1.254" address on my browser window, But it's Sho...
Hello, i have a question regarding the PRP+ : portion from the following statement is confusing from the cisco 300-115 official ccnp guilde : Sometimes the redundancy mode terminology can be confusing. In addition to the RPR, RPR+, and SSO terms, you...
Wonder if 9508 can be a vPC peer with 9504. I think it will be ok because all should be the same but the number of line cards. Also, as I know, 9k does not support multiple vdc feature, am I correct, and anyone can answer these two ? Thank you.
Hello, thank you in advance for your precious support. I have a question about s particular BGP multihoming scenario example been published on the link below: http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13762-40.html The...
I have 5 networks, each network has 2 PCs, 1 of the networks has 2 servers, 1 uses IPv4 and the other IPv6. every pc has IPv4 and IPv6. Everything is working properly and can be pinged, except for the IPv6 server. When I ping starting from it to othe...
Could you tell me what is difference between C891F(C891F-K9) and C891FJ(C891FJ-K9)?
