Collaboration Knowledge Base

This document was generated from CDN thread Created by: Joshua Marsh on 01-11-2010 08:37:55 PM I have a customer with an unusual use of VTC.  I have their C60 tied into their Cisco Unified Communications Manager via an IOS gatekeeper so that PSTN voi...

This document was generated from CDN thread Created by: Busy Rocker on 01-11-2010 02:07:04 PM Hello Guys,I am trying to control the Edge 95 PrecisionHD camera via our own application which is developed to control all our conference room equipment.Whi...

This document was generated from CDN thread Created by: Ivan Boscolo on 27-10-2010 07:07:16 PM Hi,I want to know if it's possible to read and recall presets previously saved on a system (the section in TMS console, inside a system, is: Extended Setti...

This document was generated from CDN thread Created by: Rachid . on 26-10-2010 07:54:41 PM I am playing around with some endpoints and figured out how to make a system dail out from a browser.http://192.168.255.33/formputxml?xmldoc=<Command><Dial com...

This document was generated from CDN thread Created by: Randy Ott on 25-10-2010 08:35:08 PM HI,  We are looking at purging a Tandberg 6000 MXP back to factory defaults, then reloading it through an RS232 port with the configuration files, putting a n...

This document was generated from CDN thread Created by: Rick Matos on 22-10-2010 04:32:02 PM Hi All from Toronto, Canada!!My 1st post on here and I hope I can get some answers!!The company I work for here is rolling out a huge TANDBERG solution with ...

This document was generated from CDN thread Created by: David Anstee on 21-10-2010 08:08:34 PM We have recently installed a C40 CODEC with 2x Camera's attached to it.However the system came shipped with a PrecisionHD 1080p 4x Camera and an additional...

This document was generated from CDN thread Created by: Tiziano Vignati on 21-10-2010 12:36:37 PM The unit will not boot correctlyThe console message is :Break ?Loading (#2) ... OKRunning F1.0 PAL, 2004-07-05, s50000Loading video... OKLoading audio.....

This document was generated from CDN thread Created by: Bob Fitzgerald on 19-10-2010 07:48:02 PM Hey there everyone!I've been running into questions about the wallpaper on the C-series and how it relates to layouts. Is the wallpaper the very back lay...

This document was generated from CDN thread Created by: Stephen TONG on 18-10-2010 08:13:40 AM Hello,I'm using a C20 in a system integration, but we found that the Audio Output (2x RCA) audio comes with the near-end microphone audio mixed just like a...

This document was generated from CDN thread Created by: david twitchell on 15-10-2010 08:43:07 PM I am trying to control ex90 with crestron using TCP/IP.  I am able to telnet use my pc into the ex90 with no problem.  When crestron processor connects ...

This document was generated from CDN thread Created by: MATT MEAD on 15-10-2010 04:53:37 PM I'm trolling for ideas, or techniques that would enable us to display an animated "short" in a call - Ideally, we would want to be able to post a Flash file /...

This document was generated from CDN thread Created by: Scott Stanley on 14-10-2010 10:29:17 PM I am writing an AMX module for C40.  I have written similar for virtual screen control on MXP and other codecs.  The C40 has a limited command set.I need ...

This document was generated from CDN thread Created by: Chip Wofford on 13-10-2010 04:13:12 PM The unit will not boot.  The console message is loading . . . searching . . . error . . .  missing or invalid application.Is the API missing, corrupt, etc....

This document was generated from CDN thread Created by: Toshiki Otsuka on 13-10-2010 03:10:24 PM Hi Our integrator (partner) is working on to creat a new TMS touch panel system using API and I got this question, howeever, I am still newable with TMS ...