Collaboration Knowledge Base

This document was generated from CDN thread Created by: Ian Pickford on 31-03-2010 11:03:27 AM The C60 does not have a VCR audio output like the T6000. I need to use the VCR audio output to provide mixed audio for the connection of a streaming encode...

This document was generated from CDN thread Created by: Mariusz Mieszkowski on 31-03-2010 10:46:21 AM Hi, sorry for my bad english I have big problem with Tandberg (this one - http://www.tandberg.com/video-conferencing-products/tandberg-edge-mxp.jsp)...

This document was generated from CDN thread Created by: Adrian Wright on 31-03-2010 06:17:52 AM Hi,I've found a some odd results when using the offset and limit parameters when using the phonebook search commands on a corporate phone book after upgra...

This document was generated from CDN thread Created by: Christopher Gentsch on 30-03-2010 09:15:00 PM I have a requirement to use one of the newer Sony HD3V or HD7 cameras with the TVS on a 6000MXP. There are currently 2 HD1 cams occupying the Compon...

This document was generated from CDN thread Created by: Roger Boe on 30-03-2010 10:10:49 AM Hi Stephen,This particular issue was resolved in TC3. From the TC3 releaese notes:---► Fixed an intermittent issue causing the unit to not disconnect the call...

This document was generated from CDN thread Created by: Andre Garcia on 25-03-2010 11:56:46 PM I've got a C60 TC 3.0 with Multisite installed with up to 4 simultaneous calls,  whenever I reach the limit of 4 calls and try to place another call, inste...

This document was generated from CDN thread Created by: Timothy Shire on 25-03-2010 08:33:38 PM This is a cross-post Cross-PostIt might be a good idea to have a General API category.  As i am not sure where to post this question.So this is a question...

This document was generated from CDN thread Created by: Timothy Shire on 25-03-2010 08:26:45 PM This is a cross-post Cross-PostIt might be a good idea to have a General API category.  As i am not sure where to post this question.So this is a question...

This document was generated from CDN thread Created by: Corey Gilmore on 24-03-2010 10:25:45 PM Hi,I'm programmatically creating contacts and folders, and it looks like the 1xCommand Phonebook Contact Modify command won't actually move a contact into...

This document was generated from CDN thread Created by: David Bruun-Lie on 24-03-2010 04:24:03 PM The new software version TC 3.0 for Codec C20, C40, C60 and C90 is now released.Existing AMX and Crestron modules work with the new software releaseNew ...

This document was generated from CDN thread Created by: Collin Harwell on 23-03-2010 01:46:18 PM Hey gang,I ran into an issue with two of my MXP990s (one running f8.2 and the other running f7.0) where the camera image from the MXP990 appears in 16:9 ...

This document was generated from CDN thread Created by: Martin A. on 23-03-2010 11:54:38 AM Hi!I'm trying to figure out how the CorpDir StartsWith feature works. I get nonsense results when using a StartsWith-token. For example if I type,xcommand cor...

This document was generated from CDN thread Created by: Todd Curry on 22-03-2010 11:15:13 PM One of my dealers is integrating a C90 (TC3.0) and has used the audio application to configure a lectern microphone into a new input group and connected that...

This document was generated from CDN thread Created by: Andre Garcia on 19-03-2010 09:23:21 PM I've got the demo 1.3 module loaded into my processor, but having problems creating a side by side layout where half is the far end and the other have is t...

This document was generated from CDN thread Created by: Andre Garcia on 18-03-2010 10:15:02 PM On toolbox i'm getting the following error from the Tandberg module :1. Error: Module S-3.1:S-12.3 : S2_Tandberg_C90___C60_Call_Control_v1_1 at line 265: O...