I'm using Cisco ISO 7200 (15.2M11) release product. When I enable SNMP, I cannot get the SNMP information of the device through the IPv6 global address, but I can get the device information through SNMP normally through the IPv4 address. Check the li...
Presentan el siguiente problema, alguien tuvo el mismo problema?? 2023 27 de junio 14:30:30 SWN9KSB2C2 %ICMPV6-3-ND_LOG: icmpv6 [28906] Dirección de destino duplicada fe80::863d:c6ff:fe3a:3ebf detectada en Vlan30 2023 27 de junio 14:30:43 SWN9KSB2C2 ...
MechanismScenarioTargeted EnvironmentDesign ConcernDual StackEnd-to-End IPv6 + IPv4Any Environment that ultimately needs to move to end-to-end IPv6IPv6 support in all L3 ware platforms is required.Increased control plane complexity.May introduce scal...
I have this IPv6 subnet 2402:e000:a:3:0:0:0:28/126.Range:2402:e000:a:3:0:0:0:28 to 2402:e000:a:3:0:0:0:2bI assigned IP 2402:e000:a:3:0:0:0:28/126 to an Interface and 2402:e000:a:3:0:0:0:29/126 to other router interface. But I was unable to Ping on P2...
Part of the lab mentions: Note:DHCPv6 SLAAC(Stateless Address Autoconfiguration)Reason to use DHCPv6 on a network that uses SLAAC is to push DNS and other information to the clientsSLAAC is by far the easiest way to configure IPv6 addresses, simply b...
Hello,I am attempting to ping an IPv6 address for a router's G0/0/0 port and cannot get it successfully. The IPv6 ping for port G0/0/1 is OK as it is an IPv4 ping to port G0/0/0. I think that there might be an issue with the IPv6 address itself (2001...
Existing:Currently, we have implemented the existing for IPv4 and IPv6. We enabled IPv4 and IPv6 working fine for both. But IPv6 only enabled, not working. We getting "ERR_INTERNET_DISCONNECTED".We are trying to implement the static IPv6 flow. Please...
I want to make a history of testing with the scenarioHow am I supposed to create IPv6 PDU?
So this is what my network looks like,ONR (huawei hg8240t5 router cannot be disabled) -> c921-4p -> switches etc. etc.'If I connect directly to my ONR and try to browse IPv6 websites it works fine, I can even see my ipv6 address.My ONR is already do...
Hello,I am needing assistance completing a MAP-T configuration on a CSR1000v router in GNS3.I am using Kea as my DHCPv6 server and my CE router is getting an IPv6 address and an IPv6 delegated prefix.Everything on the CE router and host Ubuntu workst...
I have configured R1, R2 and R3 with IP v6 static routes and i am able to test a successful ping between Pc1 and Pc2 however the ping fails when run from either R1 or R3 however succeeds when run from R2. Also i have enabled IPv6 unicast routing on ...
Hi everyone!I'm actually trying to setup DHCPv6-PD with AAA for my ISP on Catalyst 3850 switchs (IOS-XE 16.12), but Its doesn't seem to work as expected (AAA expecting PPP, but I don't want to use PPP, and route insertion not working at all want usin...
I understand why ::0, 4 and 8 and multiples of 4 are subnet router anycast addresses, but not 10, 14, and 18. Can anyone explain this?Thanksr4(config-if)# ipv6 address 2001:100::/126%GigabitEthernet0/0: Warning: 2001:100::/126 is a Subnet Router Anyc...
Hi,We are currently working to bring AS3223 live as a transit provider for IPv4 and IPV6 however when bringing IPv6 live we are running in to an issue where traffic via them becomes unreachable and doesn't leave our network. We've worked with them to...
Hi Guys,What is the use case for each of the IPv4 to Ipv6 migration strategies- dual-stack, translation and tunnelling? Regards
