Hi All, I have the following topology. R1,R2,R3 and R4 are CSR devices. R1(gig2)---(gig2)R2----R3(gig2)----(gig2)R4 R1#interface GigabitEthernet2ip address 100.10.10.10 255.255.255.0 R4#interface GigabitEthernet2ip address 100.10.10.20 255.255.255.0 ...
Hi,I am an avid learner to MPLS protocol . I just have a question to ask that when ldp is configured on PE routers within MPLS domain, after exchanging hello messages and building adjacencies , neighbor routers learn about FEC's and the routers local...
Hello,We need to know that what would be the procedure to have the VRF table and global routing table communicating with each other in a single router. Earlier we were using 2 different routers for this purpose, but now 1 router has to be eliminated....
Hey folks, OverviewI have the following topology where as300 runs ISIS L2 + SR. The device iosxrv5 is connected to AS100 via BGP-LU. The device iosxrv4 is the SRMS for the prefixes received from the AS100 internally. On iosxrv5 I am redistributing ...
Hello, I am trying to understand the usage of the 'import path limit' command. PE1 /. \CE P----PE3 \. / PE2 PE1 vrf:vrf definition vrf1rd 2:2!address-family ipv4route-target export 2:2route-target import 7:7exit-address...
Hi friends, Are below commands mandatory for remote-LFA or applicable only on Cisco-Asr-903 routers ? mpls ldp explicit-nullmpls ldp discovery targeted-hello Thanks in advance.
Hi,in our network we've noticed that certain routers are using one of their two upstream links, way more than the other. We've seen peaks of 80-90% utilisation on one link where the other just sits at 15-20% The topology I am working with is rather s...
Hello All, I am trying to learn BGP EVPN on cisco CSR 1000v routers. R2 and R3 are cisco CSR1000v. And R1 and R4 are cisco IOS. With the below configuration, I see route type-5 but I do not see route type-2 and route type-3. What should be the config...
Hello All, R2, R3 are cisco XR routers.R2's loopback address is 2.2.2.2R3's loopback address is 3.3.3.3.R2(gi0/0/0/1)-----(gi0/0/0/1)R3 R2: interface Loopback0ipv4 address 2.2.2.2 255.255.255.255 interface GigabitEthernet0/0/0/0l2transport interface ...
Hello All,I am trying to configure BGP EVPN on cisco XR routers. Can anyone please provide me a sample working configuration of BGP evpn on cisco XR? Thanks,Sachin
Hi there . I have configure a GRE tunnel in a test lab comprising of Cisco ASR920 series routers . All interface are GE . Tunnel status is up/up , I can ping the far end , ISIS is up over the tunnel and both routers are LDP adjacent as well . I can ...
Hello All, I am new to the BGP EVPN configuration on the cisco CSR.I have 4 routers. R1------R2 | |R3 R4 R1 and R2 have a BGP EVPN session between them.lo0 of R1=11.11.11.11lo0 of R2=22.22.22.22gig3 of R1 is connected with gig0/0...
Hallo ,i want to know from ur experince what would be the disadvantages of using NAT for ISP who has also VOIP Service, and mpls Architecture.
can anyone tell me how we can inform cisco about new bugs. regardsshivlu jain
Hello, CE1(g0/0)----(g0/0)PE1----PE2(g0/0)---(g0/0)CE2 PE1 loopback:2.2.2.2PE2 loopback: 4.4.4.4 Between PE1 and PE2 mpls is running. CE1:int gi0/0ip address 100.100.100.1 255.255.255.0 PE1:int gi0/0.1interface GigabitEthernet0/0.1 encapsul...
