Hi there !!I trying to make some test in cisco cml 2.8 with traffic engineer tunnel with explicit patch .I'm using the the topology in the image below. I have already configure tunnel with explicit path from PE1( PE1-p2-p5-p3-p4-PE3) it is working, t...
Hi all, I am looking for an IOS XR platform, which is capable to interconnect these two worlds. Based on the documentation, ASR9K could act as "EVPN VXLAN Layer 2 Data Center Interconnect Gateway", but I am not sure if this is the right feature for t...
What are the benefits over MPLS network compared to IP network?
Hi all,I am labing MPLS L3 VPNs, and as I am trying different PE-CE routing protocols, I stumbled on a point where IS-IS is not being shown as an option to be redistributed into BGP as you can see below:RP/0/0/CPU0:PE12#RP/0/0/CPU0:PE12#sh run router...
Hello experts, i am working on a lab for CCNP SP core - L3VPN between two PEs. However i am struggling to get connectivity between CE1 and CE2. both CE1s are getting routes redistributed into them so they have routes to either site. However pinging i...
I'm configuring QoS for some VRF customers and I'm undecided if I should be using explicit null (or php-disable in the case of SR). If I have a VRF customer connected to a PE and I wish to apply a policy (shaping, remakring etc) on outboud traffic to...
I have this scenario mpls vplsCE1---PE1----P0--P0---PE2---CE2between PE1 and CE1 3 interfaces 10G between PE2 and CE2 3 interfaces 10GPE1 configVSI Configvsi L2VPN staticpwsignal Idpvsi-id 22peer 10.10.10.2interface GigabitEthernet8/0/1012 binding vs...
HEllo all,iam trying on PE router create Police map for L2VPNs which will tel them via which interface they should go to P router..This is working. But how I can tie this type of communication to Flex-algo and traverse it via nodes which I need ?
Hello Everyone, I am new to segment routing. I am trying to learn the dynamic option of segment routing traffic engineering. I have 2 directly connected routers.R1---R2R1's Gi0/0/0/1 IP address 100.10.20.1R2'2 Gi0/0/0/1 IP address 100.10.20.21.1.1.1 ...
Hi everyone, I'm trying to verify that label forwarding is taking place without having to revert to a PCAP. The device I'm looking at is an ASBR in an interAS Option B setup. It is receiving a VPNv4 prefix from it's eBGP neighbor, installing a local...
Hi,I have configured following senario PE1-s1/0--------P1---P2------s1/0-PE210.10.10.1 10.10.30.2PE1 -s1/0-10.10.10.1PE2 -s1/0-10.10.30.2I have configured the IBGP between PE1 and PE2 with physical interface IP address.I can se...
Hi EveryoneI'm using ASR920 and ASR900 platforms for MPLS and metro environment and I'm facing a weird behavior on their etherchannels.for example i have an ASR920 PE with 2x10G bundled links to a C4500x.in the ASR920 i have set the load-balancing me...
Hi @Harold Ritter ,Greetings !!!!!!!!I have one query with segment routing forwarding data. I am sending some bytes of data(1500000) from XRV1 to XRv2 via SRpolicy tunnel .I see same count is updated in SR-TE forwarding database. But when i do SNMPw...
I have setup of 4 routers R1 - R2 - R3 - R4 . They are connected as shown. I have also setup a GRE tunnel between R1 and R4. The tunnel status is up and protocol is up. I have configured tunnel source and reach ability related configurations in R1,R2...
Hi All,i have a little confussion and couldnt relate rd and rt values. i have read many articles and posts but still couldnt uderstand the relation.scenario:vrf definition CLIENTSrd 32052:2address-family ipv4 vrf CLIENTSroute-target export x:x route...
