Hi All, I am having an issue with a design in which we have around 50 small sites which are connected to main datacenter through MPLS. Last mile links are around 5-10 MBPS. There is a firewall which is shared among these sites and it is located at Da...
-
Buying Recommendation
(17) -
Cisco ACI
(1) -
Cisco Cafe
(2) -
Community Ideas
(3) -
MPLS
(5,554) -
Network Management
(1) -
Other Networking
(1) -
Other Routing
(2) -
Routing
(2) -
Routing Protocols
(2)
Forum Posts
HI guys I got something problem about MPLS VPN OptionB,specially the traceroute.And here is my topology some reason of our company,there is only one router in BGP65000,which bulid EBGP neighbor with ASBR in BGP65001。 now the R10 can communicate with...
I have configured a single Hub and 2 spokes in gns3 and eBGP is running between the hub and the spoke routers.Wan to Wan reachability is fine but unable to reach from Spoke location C.E to other spoke location C.EBetween Spoke PE to CE im running sta...
Hi, we have an ISP provided private MPLS network. We've left the MTU on the CE MPLS interface as default ie 1500.Reading around these forums, it seems that you can increase this to prevent fragmentation?Should I do this or leave it at it's default? E...
Dear all, I want to deploy MPLS in IP tunnel environment so i tried to create on a pair of ASR 920 a GRE tunnel via IP environment for testing, enable ospf and ldp on the tunnel. Everything seems fine but when I establish a l2vpn service (xconnect),...
Resolved! BGP UNSHUT CLARIFICATION
HI, I need small clarification on bgp unshut. I actually need to unshut a bgp peer ipv4 for a vrf Voice_data. While doing it, i did not get into the address-family ipv4 vrf Voice_Data to unshut the bgp peer 135.45.70.225 initially due to which I g...
Resolved! Help with an MPLS/OSPF issue
Hi, I have a problem with a traffic between PE01 and PE03 (please see attached diagram).When PE03 tries to reach a network in CLI, this traffic uses MPLS, but when it returns it uses generic IP, it is normal? How can avoid this behavior?I want to put...
Resolved! Difference between L2VPN and L3 VPN
Hi, I read an atricles on an internet but still bit confused for the use and defination of L2 & L3 VPN. Can someone please explain below terms and its usage : 1)L2 MPLS VPN 2)L3 MPLS VPN
Hi, I have an ASR1001x and want to enable the "neighbor x.x.x.x send-label" command, but it's not available to me. I have an IPB license, but I thought since licensing seems to be honor-based that the command would be available on all flavors even ...
Hi All, I have to propose a design for a client in Africa but the connectivity seems to be a challenging area. The Fibre cable option is not there and leased line is unstable. I have to connect several sites and of course a new DR site has to be est...
Hi All, I would like advice from the community on how best to provide a redundant internet breakout for one of our VPN customers. The customer Has a VPN with one Internet breakout. But now the customer requires a redundant internet access at our se...
Curious Question,Is there a way to report Bugs to Cisco if one dont have a contract with Cisco?RV345 obviously does not fulfill spec, behaves differently than previous model…Routers delivered directly from Cisco, no 3rd Party involved…Replacement und...
Hello, Cisco Community. Can someone verify that xconnect between ME3800 and 6500(WS-6506(SUP VS-S720-10G) and ME6524) should work?I have tried many different configurations, but neither of them works. Xconnect is up, but all I get is unidirectional ...
Delete. No responses received.
I am trying to establish qinq over atom between 2 ASR-1001x running mpls in between. Everything comes up after configuration but I am not able to ping each other. At the same time layer2 mpls- atom with single vlan is working fine. Instead of t...