MPLS

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Forum Posts

Hi All,I need to a quick inputs from you guys.I am having c2900-universalk9-mz.SPA.152-4.M4.bin IOS. (CISCO2921/K9)the issue is I am unable to type pseudowire-class command. i searched few thing on cisco forums which they said its required data + sec...

dnsroot13 by Level 1
  • 5284 Views
  • 3 replies
  • 0 Helpful votes

Good afternoon experts, I have two directly connected Cisco 7609 routers running MPLS with OSPF being IGP,  and a EoMPLS VC has been created. On router 1: interface Vlan100ip address 192.168.168.2 255.255.255.0xconnect 10.200.0.158 100 encapsulation ...

Eric Xu by Level 1
  • 1442 Views
  • 7 replies
  • 0 Helpful votes

I have two ASR9000 running 5.1.3. They are connected back to back using mpls protocol.When i enter the command 'show mpls forwarding summary' i've got the following output:        sh mpls forwarding summary        …        Pkts dropped:    46958     ...

1pgordo by Level 1
  • 1410 Views
  • 2 replies
  • 0 Helpful votes

Resolved! allocate-label all

hi experts, I have 2 doubts : plz help 1.what is the use of  "allocate-label all" : command ? eg : address-family ipv6 unicast         allocate-label all 2. under which scenario we use below config ? ipv4 address under ipv4 add family. address-fami...

Hi, Our multiple sites are connected by MPLS coming from 1 ISP provider. We will be adding another site but our current provider does not have local carrier available so we have to use a different ISP. The new circuit is already provisioned and acco...

Gentry by Level 1
  • 1631 Views
  • 2 replies
  • 0 Helpful votes

Hi all I have MPLS network with OSPF as the underlying IGP , my current two route reflectors are ASR9010 The current design is in-band route reflection , what am trying to implement is to pull out these two routers and use them as MPLS PE and change ...

mkhalil10 by Spotlight
  • 966 Views
  • 5 replies
  • 0 Helpful votes

I hear this term : "intenret VRF" ..when they are used ? any simple example of deployment will help in understanding. thanks

I have a 2911 router with a T1 circuit terminated on a VWIC3-2MFT-T1/E1 module. I frequently observe logg entries in the router as shown below. When these conditions occur, we lose Serial0/0/0:1 IP communications. May 11 01:52:10: %MARS_NETCLK-3-CLK_...

Resolved! AVPN

CER: 192.168.xxx.3PER: 192.168.xxx.4VLAN ID: 50AT&T ASN: 13979CUSTOMER ASN: 65103           VPNID / NAME: 500554 / I have 7 locations that will be converting from MPLS T1 line to ATT AVPN. I haveCisoc 2911 router with Gigabit port Ethernet port. Att...

I'm learning about MPLS and just had a quick question-  Does the LDP and BGP processes in IOS somehow tell each other what labels they have assigned to avoid conflicts for the label IDs?

wfgeorge3 by Level 1
  • 1177 Views
  • 4 replies
  • 0 Helpful votes

Hi, Got 2 Cisco 6500's and want to span the layer 2 so we can migrate VM's from one to the other.  I have got xconnect on an interface and a GRE tunnel up and running.  xconnect is up and senting and receiving but I cannot ping between hosts across ...

I have one CE router R9, PE router R7, P router R6 in R9, I try to traceroute 150.1.0.6, it first reach 150.1.0.9(R7), then all are * * *, there is no vpn label, may I know how to correct the error and generate VPN label, previously I can generate tr...

Mary by Level 1
  • 316 Views
  • 1 replies
  • 0 Helpful votes
Top Solution Authors