We have a cisco catalyst WS-C3850-24XS 24 port 10g switch and are unable to connect Fortinet by SEP fiber connection. So basically we want load balancing for ISP, once we connect via VLAN one side gets up & the other side of the port gets down.
We have a cisco catalyst WS-C3850-24XS 24 port 10g switch and are unable to connect Fortinet by SEP fiber connection. So basically we want load balancing for ISP, once we connect via VLAN one side gets up & the other side of the port gets down.
I am not able to configure a CISCO camera over wifi in packet tracer. I am only able to connect them to the server if they have a Fast Ethe output.Any ideas, advice or help?Thank you very much
We're trying to block all SNMP, NTP and BGP access to a particular SVI. However, when using the ACL config below, only traffic through the SVI is blocked, not the traffic directly destined towards it.So SVI VLAN901 is still responding on BGP, NTP and...
Is there a way to prioritize all traffic from a specific LAN IP address on the RV345?
I need help setting up a guest WiFi network on my RV340W. I would like guests to be able to access the internet but not our shared drives etc. I was trying to follow these instructions: https://community.cisco.com/legacyfs/online/attachments/documen...
I have this topology with two SVI with Different Subnet, how to connect them together?
Hi all, I need to have an automatic sistem config backup. I tried to create an user that have ssh access. From an external FTP server, i've created a script that logs in the switch and give the command "copy running-config tftp://x.x.x.x". But it don...
As shown in the network topology above.Regarding NetFlow FNF, I created 2 flow-records (1 each for IPv4 and IPv6), 2 flow-exporters (1 each for IPv4 and IPv6), 2 flow-monitors (1 each for IPv4 and IPv6), and then The g1/0 interface is bound with a to...
Hello, We have purchased multiple CBS250-16P-2G switches to test a new system for a client. We want to be able to individually control the POE state(POE enabled/disabled) of a given port (1-16) via a telnet interface. We have tried the following com...
hello,somehow rv340 can't resolve domains as well as send e-mails.may be someone knows which setting to change for fixing these problems. i may convert actual log file to doc file.thanks a lot for helping.keep safe !!!regards,michip.s.: whoever had e...
I want to increase my skills in using SYSLOG, I've had some luck in basic usage, but cnan't even really log things like incoming telnet sessions. Any guides or tutorials out there any one may know of that hass some deep dive or more involved/advanced...
I want to generate SYSLOG traffic, is there an article/guide that may help me with replicating syslog events on my routers and switches, as I want to analyse various SYSLG events. I have a logger set up. I wangt to analyze a range of SYSLOG logs as t...
Can someone explain to me what I need to do to get these routers to stop pinging> I included multiple deny ICMP commands and it is still pinging
Hello everyone, I want to see the bandwidth usage of router interfaces Cisco 7200 in real time is there a command to see this or maybe a calculation method? I try with SNMP and Netflow but I need the value of bandwidth usage in real time. Thank you v...
If I assign a native VLAN access port at the edge for a given set of nodes, and the header remains there Will it get treated as VLAN 10 and not Native VLAN as it moves upstream? I read about using this tactic on a Junos guide page ~ I'm not sure if ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-14-2025 10:25 AM | ||
01-13-2025 04:14 AM | ||
01-13-2025 03:56 AM | ||
10-21-2024 04:04 AM | ||
10-18-2024 12:32 AM |
User | Count |
---|---|
4 | |
3 | |
1 | |
1 | |
1 |