Hi, I installed a Cisco Network Assistant but the application does not open, instead a pop up message appears.Please see attached. Please healp, Thanks, AL-QCGH
Hi, I installed a Cisco Network Assistant but the application does not open, instead a pop up message appears.Please see attached. Please healp, Thanks, AL-QCGH
Helo I have SW c3650. I've configured SSH, RSA Key and line VTY. AAA new model is already done.Before I put ACL in VTY line I could reach my switch via ssh but when i put ACL i have network error.i have create :group object MGMT_GROUPrange x.x.x.x x...
Hello Everyone,In Cisco Prime Infrastructure, I need to take a "CORP_Job_Config-Archive" full detailed report of devices states in Pass, Partial and Fail using RESTAPI.Where I can get only the "CORP_Job_Config-Archive" daily status of RunID only of t...
Hi, For a stacked Cisco switch (2 switches), if I input the command copy running-config startup-config, will it save the running configuration file to the start-up config file for both switches? I am thinking of rebooting the switches one at a time a...
Hi, would like to understand how should i calc the no of broadcast domain given in this diagram? Given that the routers is layer2 capable and is supporting the STP function of the mesh network of switches connected.
I've resently had to upgrade from isr4400-universalk9.03.16.07b.S.155-3.S7b-ext.SPA.bin (router) and c3560e-universalk9-mz.152-4.E6.bin (etherswitch) to isr4400-universalk9.16.09.04.SPA.bin(router) and c3560e-universalk9-mz.152-4.E9.bin. Doing so I ...
I am trying to configure Cisco 3560 switch as tftp server. How do I upload files using USB (commands)? what commands should i check to verify if switch is capable of transferring files from USB.
HI,can any one help me in overcoming this problem. When i try to relaod/ overwrite some configuration in cisco IR1101 router and switch, it gives and message like [confirm]^A and message appears :do you want to overwite [confirm]^s
Hi folks,I am trying to setup a dynamic packet capture with EEM and then after the capture captures some predetermined amount of data automatically off-loads that .pcap file to my server. I have figured out how to dynamically trigger the EEM script ...
Hi the community,I have 2 ASR1001-X withe the same IOS version and the two havecrypto pki trustpoint TP-self-signed-XXXXXXX....andcrypto pki certificate chain TP-self-signed-XXXX. When I do a sh run on the first-one I can see the crypto pki certifica...
Hi, First time post on the forum but looking for some assistance. I am trying to find out if the ISR4461 supports the SM-X-64A card. The product guide suggest that this is the Service module for the 4K family of routers but on the data sheet it sto...
Hello experts, Could you please explain how to make the encrypted password for the local and enable authentication in Cisco IOS. I have tried as many password but does not work and shows the below error:(I could understand I should not use the level ...
Hello, I have a problem on getting too much email notifications because of the alerts that occur only for few minutes and then solves itself out. I have 150+ AP:s and I have a notification policy where it contains only critical conditions on AP:s. Ho...
Good day, We have a point to point link between us and a client. We have a cisco router 2911 on our side and the cable is on a GigabitEthernet0/1 interface. We are monitoring the link on our end using snmp and we receive alerts whenever the interface...
Dear Team , I created wlan wireless_guest web authentication using local authentication , everything works well i have only one problem ,after web authentication ( username and password) click to submit user get access to entire corporate network ,...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-23-2024 05:52 PM | ||
04-23-2024 12:20 AM | ||
04-16-2024 04:45 AM | ||
04-16-2024 01:33 AM | ||
04-13-2024 12:00 PM |
User | Count |
---|---|
4 | |
2 | |
2 | |
2 | |
1 |