Hi, I'm fairly new to packet tracer and have been familiarising myself with certain connections, one of them is DSL. I understand how it works and functions but just wanted to ask for step by step instructions via packet tracer on how to set a dsl ...
Forum Posts
Les planteo el siguiente problema que deseo me ayuden a solucionar.Estoy instalando nuevamente la máquina virtual CSR1000v en VirtualBox, según las instrucciones del Lab 7.0.3 del curso DEVASC, se anexa y utilizando los archivos que tambien anexo.Res...
I am trying to duplicate two C9800-40-K9 units. I followed the guide properly Connect RP and over time *Oct 28 05:13:31.502 KST: %IOSXE_REDUNDANCY-6-PEER_LOST: Active detected chassis 2 is no longer standby*Oct 28 05:13:31.509 KST: %IOSXE_PEM-6-REMPE...
I am trying to enable esi multihoming on a new deployment. The [evpn esi multihoming] command is not found and gives an error when its tried. We are running C93240YC-FX2 switches on version 10.2(2). We have been follwig this guide as a reference. ...
Hello everyone,I have added some old cisco switches like 2960-48TT-L to our prime. Now, I am encountering a problem when attempting to activate SNMPv3 for Prime. Typically, I create a group and user configuration as follows:snmp-server group [group-n...
Does Cisco support the use of Apstra as an alternative to APIC or Nexus Dashboard on N9K HW?
Hi allI have some problem on my switch I have Topology like this :CoreSW ---> MainSW ---> WLC5520 -- APs ---> Clientand when my switch got this packet excess defer framesand this Output DropsI have no Internet Access on my APsmaybe someone can explai...
Hello friends.I have a 2960 switch, running OS 15, image LanLite as belowFrom my PC (in different subnet with IP MGMT of switch) , I can ssh to switch normarlly.But when I show running config of switch, the straight thing is thạt : it does not have i...
We have Cisco Catalyst C6807-XL with version 15.4(1)SY3 and C9407R with Version 16.10.2r[FC1].They are connected over EoMPLS and we like to have MACsec configured on the each trunk interface for a security.I don't know my switches are supporting MACs...
Resolved! SNMP SETUP ON FMC
Hello Guys,Just configured SNMP traps on my FMC for FTDv to PRTG. For some reason i get diagnostic Interface is shutdown, yet am able to ping my management Interface.How is this so, and how do i resolve this.Thank you.
Hi Networkers,I would like to get some suggestion on designing my enterprise network.I will explain the current design and my requirements.We have a 3- tier architecture with Core layer (Cisco 3650 stack -2 devices) , distribution layer (cisco 4500 -...
Hello Team,kindly i need your assistance as i have 2 switches okay first one is a core switch Cisco Catalyst 4507R+E with port 10G and a 10G GBIC module okay and the second switch is SG200 now i need to connect the 2 switches switch SG200 has a 1G G...
Hello, In the company we have a few unmanned sites where we have a few routers 829 with 4G connection that sometimes goes down, we need to request the signal refresh with the Service Provider but it usually don't work, so we need to dispatch a field ...
Hi, We have two firewall clusters (Firewall 1 and Firewall 2), directly connected to each other as per Image below in Active Passive mode. The problem I am facing here is, If any link on Firewall 1A goes down, Firewall 1B will become primary but ther...
Hi all,I'm making EEM script to drop MAC address duplicate in syslog.If syslog msg "%IP-4-DUPADDR: Duplicate address .... " => Drop MAC address by EEM script in my Cisco device.- Model: WS-C3560X-48- IOS verion: 15.0(2)SE10aEEM and CLI command to co...
