I'm trying to troubleshoot acl-drop's in my ASP drop capture. Unfortunately, a large number of these drops are from my outside interface, folks trying to come in to particular resources. Is there a way to capture this while filtering out that Interfa...
Forum Posts
Resolved! No Real-Time Log Viewer in ASDM 7.8(2)
Hi. I update my cisco ASA 5508-X recently to ASDM 7.8(2) and ASA to 9.8(2), since then i cannot access to: Monitoring > Logging > Real-Time Log Viewer When i click in the button "View...", nothing happens. In my other cisco ASA 5508-X with ASDM 7.6(2...
I have a 5505 at home with a 10M/1M ADSL connection. The issue I am experiencing is that when the upload gets saturated my download speed drops and latency goes through the roof (over 1000 ms). I think prioritizing outgoing TCP ACKs should solve the ...
HI, I'm migrating from ASA to FTD and I'm wondering how to deal with Service policy rules ? Should I just create ACP rules for each one with action permit ? Regards,
I was updating the firmware from 8.2(1) to 9.1.(7)23 due to the security vulnerability. The ASA never came back up. I cannot access the Rommon mode. This is how the console port output looks like: CISCO SYSTEMSEmbedded BIOS Version 1.0(12)13 ...
i can traceroute 8.8.8.8 from fw fw/pri/act# traceroute 8.8.8.8 Type escape sequence to abort.Tracing the route to 8.8.8.8 1 x.x.x.x0 msec 0 msec 0 msec 2 * *x.14.214.71 0 msec 3 x.14.214.70 0 msec 10 msec 0 msec 4 x.170.246.225 0 msec * 0 msec 5 x.1...
I have an ASA 5506-X with the Firepower module at v 5.3.1.6 (build 16) and a Sourcefire Defense Center running at v 5.4.1.3 (build 55). I know, these are both really old. I've found all of the documentation on upgrading from 5.4.1 to 6.0 and bey...
Hello, Cisco ASA version: 9.8(2) I have prepared port forwarding and it is working properly, but if I want to add port https(443), I receive error message (because this port is used for webvpn and asdm). I have already found out, I can change...
Resolved! FMC 6.2.2 deploy button unavailable
Hi, Does any one get this situation before please : The deploy button is unavailable and turning indefinitely... thanks
Hi, I having a strange issue with a Firepower 9300 Chassis running FXOS 2.0(1) Normally you should be able to edit the SSH and HTTPS access list, either from the WEB GUI or from the CLI using the ip-block commands from the /system/services/ menu, bu...
Can't seem to find the right command but I forgot what I must enter on the device first before capturing and saving a running-config file using putty, but not showing those weird characters when hitting the space bar. Also, how to change it so when y...
Resolved! ACP rule migration from ASA to FTD.
HI, I have a simple question : I have to migrate from ASA to FTD 2110: In ASA i have a rule based on "IP" as service with action Permit. In FTD there is no "IP" object in rules, should I simply add it as prefilter rule with action fastpath ? ...
Hi Team,I have tacacs configured for central authentication to my ASA 5585 (8.4.2) firewalls. Now I want my polling server to use same credential for ssh and other snmp polling operations, how do I do that without configuring any local snmp v3 user o...
Resolved! Firepower Re-image in Active/Standby ASA
Hello, can you verify the steps for re-imaging the firepower modules on ASA in active/standby? There's no worries for being without the IPS for couple hours so I'm planning on doing the following: on the primary: 1-Copy the boot image to flash 2-s...
hi, i am new to Cisco firepower and i need your help, i had some issue on reporting and make custom report i want vulnerability detail with IP address of source of vulnerability .
