I am looking for clarification about how the ASA handles scanning threats and the function of the threat detection command. After reading the documentation the function of the "threat-detection rate" command is still unclear to me. When does the AS...
Hello,I see Cisco recommends that you should connect a dedicated switch between two ASAs for configuring LAN failover and stateful failover, instead of connecting a cable directly between the two ASAs. Does someone know what is the advantage of putti...
Hi everyone ...I have two 6509 configured with VSS, in each 6509 we have one FWSM and IDSM2.We have configured the FWSM with contexts and we have Failover working fine.Now we want to configure IDMS as IPS inline but we want to use both IDSM in load b...
Good Evening,I'm kind of stumped here, I have an ASA 5505 that during preak usage, likes to lose it's connection to the cloud for 50 seconds. The device is alive and kicking, can route between different interfaces, but it's connection to the cloud di...
Hidoes CSM 4.2 has full ipv6 support ?e.g. add routes for ASA over the CSM 4.1 does not work Any documentation about CSM 4.2 new feature available ?THX
Hello,So, I have two asa 5505 routers. Lets say "router A" has 50 user licenses and "router B" has 10. What it comes down to: I have to switch the two routers around. Router A is going to the office where router B is and visa versa.I am wondering ho...
Here is my configuration. I can ping from the Router out to the internet. From the LAN I can ping the "inside" port and the "outside" port, but nothing past that. I also have no other access (web, smtp, etc). I am new to this device and zone bas...
Hi all,I have a challenge with the IPS module in the ASA5520, the ASA-SSM-10. When we start a test to connect to the webservers I get a inspection load of 100% and traffic/performance will slow down.We test with 63000 sessions per minute which perfor...
Hello,We have 4 remote offices coming through the WAN to use HQ Internet Connection (10/20 Mbps)Since all remote offices and HQ are figthing for bandwidth, I would like to implement QoS.The major problem is when they are downloading. Some times, time...
I am in need of the steps to configure an EEM script to switch out the ACL applied to traffic coming "IN" on the vlan1 interface. I have one acl applied that works for both broadband and dial but customer wants to filter traffic allowed back thru vpn...
Howdy Folks,I've been trying to figure this one out for quite a while. I currently have 2 inside interfaces (data, phone) and I am moving to 3 inside interfaces (servers, workstations, phones). I have not been able to get any traffic between the in...
Hi Team! Here's the scenario: Bunch of networks -- ASA -- ISP1 -- ISP2 The deal is that the customer wants one of the networks 172.16.x.0/24 to use ISP2 as its main exit, while keeping all other networks using IS...
Event Date/Time : Wednesday, September 28 · 9:00am - 10:00am pacific time. For your local timezones, see http://bit.ly/oby74nLocation: Facebook Fan Page ( http://www.facebook.com/CiscoSupportCommunity ) Join us to discuss and ask questions on ASA...
We have acquired a site that has a SOHO firewall with a single GLOBAL ip address. Someone got very creative with the PAT rules and setup port address translations based on not only destination port, but source address. For example if a user was com...
Hello , we have two ASA 5520, on the failover unit is showing LU allocate xlate failed. We read on http://www.cisco.com/en/US/docs/security/pix/pix63/system/message/pixemsgs.html that it could be a memory problem , but have cheked it and we have 85% ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM |
| User | Count |
|---|---|
| 5 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
