Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Dear collective Cisco geniuses...I upgraded my ASA 5520 with the latest image. Now I get an error upon launching ASDM.Version Mismatch:Your ASA image has a version number 7.2(4) which is not supported by ASDM 6.4(1) Please use Device Manager version ...

robprescott by Frequent Visitor
  • 2539 Views
  • 1 replies
  • 0 Helpful votes

Hi,I would you like to know if its possible to use a cisco router like relay syslog.Infact, I have 1 router (router A) who can't access directly to the syslog server, and an other router (router B) who can access to the server. Of course, router B an...

051236589R by Community Member
  • 1461 Views
  • 2 replies
  • 0 Helpful votes

Hi.in my office i do have a cisco 877 to get access to the internet where i do have a static  IP address. The LAN has IP 192.168.0.0/24 with 192.168.0.1 to be the router.in my LAN i do have a voip server which is on 192.168.0.50all of the PCs have ac...

I have a couple of  ASA with some SSM-10 and SSM-20 modules. My CSM is currently not working on the auto update side and i'm a bit behind on the updates till I  figure out what's the issue.. Can somebody tell me what link can I manually downoad the s...

kwanm63my by Level 2
  • 1780 Views
  • 2 replies
  • 0 Helpful votes

Hi,I have a ASA 5505 which stops pretty early in the boot sequence.This is all that shows up,CISCO SYSTEMSEmbedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45Low Memory: 632 KBHigh Memory: 251 MBPCI Device Table.Bus Dev Func VendID DevID Class       ...

Facing problem while configuring Active/Standby failoverNote :- Please help on how to enable the VPN-3DES-AES and another ASA BoxMate's license (VPN-3DES-AES Enabled) is not compatible  with my license (VPN-3DES-AES Disabled). Failover will be  disab...

abhi-adte by Level 3
  • 1905 Views
  • 2 replies
  • 0 Helpful votes

Dear Support,Can somebody clarify for me the difference between creating rules using Access rules and using ACL Manager?when i create a rule graphically, i see it on ASDM and when i create the same rule using cli, i cannot see it on Access rules, i c...

zain_gabon by Level 4
  • 26685 Views
  • 33 replies
  • 0 Helpful votes

I am using a three interface ASA config (Internet, DMZ, Inside).  The DMZ and Inside networks are both RFC 1918 space however it is against our corporate policy to allow our DMZ IP space to be internally routable, therefore we must target routable IP...

Hi Guys,I would like to nat using the static command and I would like to nat 10.180.1.0/24. Will the command syntax will be look like thisstatic (inside,testdmz) 10.180.1.0 10.180.1.0 netmask 255.255.255.0Is the above correct ?Tks

Resolved! ASA fixed version

Dear all,How can one detect which ASA fixed version a ASA is running. When I issue the show version command I only see 8.4(1) but I also want to know which "fixed" release the ASA is running. The reason I want to know this, is that the Cisco bug tool...