Hi all I have two ASAs configured in Active/standby failover in single context mode .Is it possible to configure failover such a way that when Primary unit comes up after filover, it becomes automatically active ?Thanks in advance
Hi all I have two ASAs configured in Active/standby failover in single context mode .Is it possible to configure failover such a way that when Primary unit comes up after filover, it becomes automatically active ?Thanks in advance
Hi All,I had a very basic level question regarding using ASDM for an ASA5500 with a Security Services Module. When logged in via ASDM, I do not see an IPS tab/section. Could this mean that the SSM is not configured at all?Thanks in advance for any ...
I have a question about NATing I do not fully understand.Normally when I think of NATing an IP Address, I think in terms of the outside interface and public address subnet. If I have a server on the inside network and an available public address in m...
1) If the ACL between the 2 interfaces is "permit all", does it allow the broadcasts (like netbios) to be relayed to the other interface?2) And does 515E have an ip address helper? I don't see any commands relating to ip address helper when I do "?"...
I have been reading the ASA Configuration Guide 8.0 and trying to use the command "switchport access vlan 10" under an inteface. Unless I am doing something wrong, why are these commands not available on my device. I'm using Software Version 8.0(4).
Hi -I recently purchased 2 ASA 5510's. I also have two ISP connections. How do i configure the two devices to perform WAN failover for each other? I have read the documents online but the active/active failover document seems to apply only to LAN ...
Hello,Any ideas on why the High and Medium Application Security Policies are disabled in SDM? I'm using a 3845, the image is "c3845-adventerprisek9-mz.124-5b.bin"Thank you.
I have a Pix515e running Version 6.1(4)when I go to add access-list it allows me to add them giving no error, but when I do a Sh configuration it doesn't show what I have added.I added the same lines to a Pix515e running version 6.3 and it works fine...
Can the IPS Express Manager software be used on a server with SAN storage? As far as you know there are no issues with using a SAN on the server the software is installed on. Is this product setup to have a backup IPS Express Manager Server for a p...
My ASA5510's are configured as Active/Passive, but they are licensed for Active/Active. Has anyone ever seen this and what issues will this cause on failover?
plese help me. where to start, I am reading but, I need a ideas, My IPS is 4240 and my ASA 5540
I need to get 400 users on the Internet with a pair of ASA5520's for high availability. If I get two 250 user models will this work? I figure that when both boxes are working each should have approx 200 users. If one fails then I understand all us...
need help with permitting eigrp through a transparent security contextjust two vlans, with one using the managed ip addresscan't locate whitepagethanks,
On an IPS is there a way to create a filter so that it will not trigger any signature based on a specific source IP?So for example no signature will fire for source ip 10.1.1.1
I'm trying to give access from host A into the ASA. When I put the ACL in, it gives me a error saying Invalid Hostname. I'm sure the ACL is correct. Not sure if I need to just create a static routing or something else. Here's the ACL's I'm trying to ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-10-2024 09:25 AM | ||
09-02-2024 07:16 AM | ||
08-30-2024 11:35 AM | ||
08-19-2024 03:53 AM | ||
08-14-2024 08:06 AM |
User | Count |
---|---|
7 | |
4 | |
4 | |
3 | |
2 |