Hi,We have ASA 5520 in our network. Blue Coat (SG 510) is connected behind the ASA for web filtering. Blue Coat is configured as transparent device.Blue Coat IP is 10.138.74.5.Now the problem is from last one moth I am getting high BW utilization iss...
Hi,How do I disable NAT between two networks on the same asa. Right now the NAT between my two networks 192.168.1.0/24 and 192.168.200.0/24 isn't working so I figured I could do without it.Tried no nat-control without any luck.Part of my config:inter...
I would like configure my firewall to allow IP Telephony services over the VPN. Kindly advice on what i need to do.
I have a basic question , please answer it What will happen if I put like given below in my ASA ? nat (inside) 1 10.1.40.202 255.255.255.255 0 0global (outside) 1 202.25.25.65 netmask 255.255.255.255static (inside ,outside) 202.25.25.66 10.1.40.202 n...
HiI have Router --- ASA (Transparent)----Switch and just wonder if it is possible to configure secondary IP on the router interface which is connected to ASAso there is plenty of room in terms of LAN IP range. Or to implement this, do I have change A...
Hi, I want to block the usage of internet for Inside users except few websites. Please advice.The QA testing team test some application by connecting remote servers which is connected by STS Tunnel. And I have opened IP protocol between both Sites an...
Just installed the FWSM in our 6513. Was reading on its configuration. It states under assigning VLANs to the FWSM under VLAN guidelines that you can not use VLAN 1. We do use VLAN 1.To change away from VLAN 1 would require a lot of changes on our ca...
Why is web browsing slower by about 1/2 when go to web thru VPN. When I browse web directly from PIX to Internet I am twice as fast. Could it be MTU settings?
folksi'm new to the asa and i have a newly configured asa 5540 and i'm trying to ssh through it to an external routerroutes etc are all okwhen i try an ssh i can see the outbound session built but the inbound reply is deniedi suspect this is because ...
Hi,PIX515E showing Not enough memory when saving configurationflashfs[7]: 10 files, 3 directoriesMessage #36 : flashfs[7]: 0 orphaned files, 0 orphaned directoriesMessage #37 : flashfs[7]: Total bytes: 15998976Message #38 : flashfs[7]: Bytes used: 15...
Hi All,Do i need to configure trunk configuration on ASA interface which is carrying multiple VLAN traffic ?ThanksMadan
when i do a show arp on my pix 501 i get this back:AB01-BM-PIX(config)# show arp outside 192.168.1.1 0002.cf0f.7109 outside 10.228.192.110 0002.cf0f.710e outside 67.79.67.245 0002.cf0f.7109 inside 10.13.2.106 0080.6469.418c inside 10.13.2.103 0080.64...
Hi...I have an ASA 5540, and im testing the logginng. When I telnet (port 23) my internal interface, the log shows me that the connection was denied. All rigth. But, when I telnet with another port, for example 5858, the log doesn't show me anything....
The Standby ASA5520 started logging the following message sequence for each interface:(1)%ASA-1-105005: (Primary) Lost Failover communications with mate on interface ________(2)%ASA-1-105008: (Primary) Testing Interface ________(3)%ASA-1-105009: (Pri...
Hi I configured natting for the dmz server to access from inside interface...let say my dmz server ip is 172.80.50.20 and configure a local natted ip as 10.80.60.20. after i enabled the natting i am not able to access the server using dmz ip( 172.80....
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-14-2026 01:46 AM | ||
| 11-12-2026 11:33 AM | ||
| 11-12-2026 11:09 AM | ||
| 11-12-2026 12:41 AM | ||
| 11-06-2026 12:20 AM |
| User | Count |
|---|---|
| 1 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
