I am trying to create ACL using object groups which contain protocols in 6500 FWSM configuration.I have a list of protocols that has to be identified by tcp port numner; for example: tcp ports 33000, 8095, 8090 etc. But I can only see the protocol nu...
Hi.I am having issue with a Firewall attached to our Telco router.I have been told by the Telco (and had confirmed) that their customer facing interface is force set to 100MB/FULL DUPLEX. However no matter what I set on the ASA (Auto/Auto or 100/FULL...
Hi all,I have a DMZ with actually 2 servers.I need to limit bandwidth to one of them to 4 mbps. I don't find clear information, i found a link in few different forum that seems to answer my question, but it is dead link(http://www.cisco.com/en/US/pro...
Hi, Currently three sites are connected with ASA 5505 through IP Sec STS VPN Tunnel. We have 1 MB link. Now I want to know that what is a minimum speed required for a single tunnel so that it works better. Does Cisco recommands this?? The Traffic dat...
hello, what's the current thinking these days for an all-round enterprise firewall solution based on the FWSM. I'm most interested in firewall log queries/reporting/alerting/archiving.Let's say for example, I want to see a report showing firewall act...
Hi,What I am thinking to create three three V-lans on L2 switch like :-1) Vlan-100192.168.1.0/24Int 12) Vlan-100192.168.2.0/24Int 23) Vlan-300192.168.3.0/24Int 3Now one of the interface 4, want to use as a Trunk port which will be connect with direct...
Hi,we are trying to run custom executable in remediation process with non-admin rights. As I understand it there are following requirements in order to be able to do that:1) CAA Stub have to be installed2) Application have to be signed with trusted c...
Dear sir,i have three servers connected to switch from that switch to i connected to firewall through this firewall iwant to communicate this servers and already i configure the firewall plz guide me if any changes require.iam attaching my config.tha...
Can I use network object-group as source addrese(s) in ACL and just a network ( not a group) as target in the ACL ? for example:object-group network TESTnetwork 1.1.1.0 255.255.255.0network 2.2.2.0 255.255.255.0access-list MIX extended permit ip obje...
Hi, Generally I take backup in text format (Noteapd) and now I want to know the process of roll-back of text format backup into ASA, if we need it. Thanks.
Hi,I have a public /24 address range that i want to apply to a DMZ on a pix 515. The outside interface on the pix is connected to a Cisco router using an private address 10.x.x.x This router is running bgp and eigrp. I need to advertise the DMZ range...
Can anyone give 2-3 good reasons for doing url filtering using the CSC instead of MPF? Is there a limit on the number of entries in the list? How about other resource or process hits to the ASA?
I have two segments in 6500 FWSM module in routed mode, Vlan A and Vlan B with same security level of 70. I want to allow IP traffic from A to B and Vice versa.a. I have "same-security-traffic permit inter-interface" in config. DO I still have to use...
Hello -Has anyone connected a 1841 to AT&T Residential Gateway for Internet Access? I have a Cisco 1841 with the Cable HWIC card, but know that since I have TV along with Internet through the Gateway I can't get rid of that
i have one global ip address x.x.188.5 and I have to servers 192.168.1.219 and 192.168.1.220. I want to advertise these servers over the Internet on the following HTTPS & SSH.How can i advertise these servers with one global IP address. Please help m...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-24-2026 02:14 AM | ||
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM |
| User | Count |
|---|---|
| 2 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
