Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Resolved! ASA 5520 Problem

Hi,I've bought an ASA5520 and I could not access the console port. Another thing I think it's not normal is because the Status LED is amber as soon as turn the switch on. Is this a hardware problem ???Thank you.Neirival (Brazil/Angola)

hi all...I have a dns server on outside and a dns server on my dmz.. they are sending updates between each other..Problem is that this update that normaly take about 1 or less second are trough the pix using up to 20 min..This is logg6|Oct 24 2006 08...

jenseike by • Level 2
  • 1135 Views
  • 4 replies
  • 0 Helpful votes

Hi There,I'm trying to lookup a way to do source-based routing in PIX to achieve the same functionality of the "route-map" command in Cisco routers; is there an equivalent command for it in PIX version 7.x? I recall that this wasn't available in prev...

Hi, I need to redirect MS Exchange (smtp, pop3, imap4, http, https) ports on a CISCO pix 506e firewall using PDM 3.0 (no CLI). PIX public IP: A.B.C.D, mask 255.255.252, MS Exchange server is : 192.168.105.8, mask 255.255.255.0, gtwy. 192.168.105.1 Al...

alex_sa by • Community Member
  • 968 Views
  • 2 replies
  • 0 Helpful votes

Hello, I have ISP--Outside_Router--ASA. THe subnet between the Outside_Router is private subnet 192.168.0.0/30. However, all my NAT/PAT I am using public IPs. Now we need to setup VPN tunnel from PIX to remote office. How can I do that? I mean since ...

m-haddad by • Level 9
  • 1068 Views
  • 5 replies
  • 0 Helpful votes

Is this a problem with the DNS fixup? I have a new PIX 501 that I have in place on my home network - Its attached to Verizon FiOS via PPPoE. DNS queries from PCs on the network work perfectly, however, the DNS queries initiated by the Verizon CATV Se...

abatson by • Level 5
  • 622 Views
  • 2 replies
  • 0 Helpful votes

Right now most of the rules I am creating are drop rules while doing the initial tuning of my MARS box. When I use the query to save as a rule, it apprears that you can only save it as an inspection rule and never as a drop rule. Am I missing somethi...

mmorris11 by • Level 9
  • 1029 Views
  • 2 replies
  • 0 Helpful votes

1599 10/19/2006 15:27:36.790 SEV=5 IKE/231 RPT=8 210.x.x.x Group [210.x.x.x] Could not find centry for IPSec SA delete messageHi after a document which will allow me to decifer and understand VPN concentrator messages like the above.ThanksSimon

I am configuring a site to site VPN with a Cisco ASA 5510 on each side. Site A and site B each have several local router hops. We currently run Rip v2 at each site. Is it possible to forward Rip broadcasts through the VPN or is it time to look at ado...

jpierson by • Community Member
  • 822 Views
  • 1 replies
  • 0 Helpful votes

The SVR is on VL60, the PC is on VL80. So, PC(.25--VL81--GE0/7--VL80--SVI 80--SVI60--VL60--SVR(.10)Sensor interface GigabitEthernet0/7 is assigned to trunk all Vlans 1-4094CAT65K-PODX#sh ru | in intrusionintrusion-detection module 6 management-port a...

dmarsh by • Community Member
  • 1206 Views
  • 4 replies
  • 0 Helpful votes

My entire network access everything on the outside using Nat0. Is it possible to have the entire network acces a single outside destination address via a nat'd address?So, if I'm going anywhere on the outside I don't get address translated but if I'm...

Review Cisco Networking for a $25 gift card