Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi, We have a VPN concentrator 3030 on which multiple site-to-site VPN's are configured.There is an issue with 1 client who tries to FTP through his VPN tunnel to a FTP server at the client end...The download works but upload doesn't...Anybody who ha...

rags123 by Community Member
  • 1149 Views
  • 1 replies
  • 0 Helpful votes

Hi,The aaa authenticatin on the PIX is enabled and to use the LOCAL user database. A user is created (username ABC password XXX privilege 15) on the device. What's the command for user ABC to change his password?Thanks.

I have a question about how ACL's are applied. I already have a pretty extensive ACL applied to the in interface outside. It seems that when I apply a newly created ACL (with a different identifier number) and then remove it, the original extensive A...

abruso by Level 2
  • 573 Views
  • 2 replies
  • 0 Helpful votes

We have a PIX 515e that we are going to install soon. The unit has 6 interfaces and 4 of them will be used. The FOS version is 6.3. NAT will be disabled on all interfaces. We will have the outside (security level 0), inside (level 100), DMZ (level 50...

jeff by Level 3
  • 582 Views
  • 2 replies
  • 0 Helpful votes

I know routers and switches quite well, but I'm weak with the PIX OS. Given the config below, can anybody tell me why I can't telnet to the inside interface from a device on the inside network? I get this error: "402106: Rec'd packet not an IPSEC pac...

Kevin Love by Frequent Visitor
  • 706 Views
  • 2 replies
  • 0 Helpful votes

For the last 4 working days, we have had to hard start our 3.6.1 3030 early in the morning before our ezvpn pix 501 hw clients could pass traffic. They connect, but nothing goes through the tunnel.The syslogs show nothing to say the 3030 was restarte...

bswitzer by Level 1
  • 1185 Views
  • 2 replies
  • 0 Helpful votes

I'm getting a fair number of the following, I notice as I look in the logs to track down a problem. Anybody know what it means and the significance?Group [group] User [user]IKE AM Initiator FSM error history (struct &0x647280c)<state> <event>:AM_DONE...

bswitzer by Level 1
  • 1320 Views
  • 1 replies
  • 0 Helpful votes

When looking at my list of users in ACS, a recently created user appears. When I click on this userid to edit it comes up as USER (New User). None of the fiels are filled in. i.e. no password assigned, no description. My only choices are Submit and C...

jporter_hm by Community Member
  • 1029 Views
  • 1 replies
  • 0 Helpful votes

I have to hosted servers, one has 25 IP's the other 3. Why this was done is beyond me; however, I digress. We are taking over the firewall management and I need to set up the 506E to handle this. Does the 506e allow 29 IP's on the outside port or can...

admin_2 by Level 7
  • 657 Views
  • 2 replies
  • 0 Helpful votes

Hi,What are the possible performance problems and security issues with increasing the timeout values (conn especially)?Are there any recommendations as to the max values? I cannot find anything other than syntax on the web site.

aemr by Level 2
  • 1844 Views
  • 5 replies
  • 0 Helpful votes

Resolved! PIX as Dhcp server

I know the PIX can act as a DHCP server, but can it have MAC-to-IP reservations?I would like my PIX to issue dhcp for our internal network, but I need to have a few reservations for clients.

koaps by Level 2
  • 713 Views
  • 2 replies
  • 0 Helpful votes