High Level Overview of my network: Cisco 9400 at campus core, 9300s at four smaller branch schools. OSPF routing to our ISP who routes internal traffic directly to the correct building and external traffic to internet. All of these links are working ...
Forum Posts
Hi , i have primary FMC1 working fine with 3 ftd registered to it. i have setup secondary FMC and joined fmc 2 to fmc 1 . it seems that fmc are connected and getting synced but no ftd get registered on FMC-2 so FMC2 shows degraded status because fmc ...
Hi team,Question around how to verify whether SI is actually dropping intended traffic.My understanding is that SI is processed BEFORE ACP is evaluated.When I run packet tracer against an IP that's included in one of the lists/feeds in /var/sf/iprep_...
Can someone tell me what the command is through CLI to reset the management IP address on a Firepower 1010? The Cisco documentation for this is wrong. It does not provide any examples and no matter what I try, it says syntax error.This is what I am...
Hello,Can someone help with OIDs for SNMP NAT monitoring on Cisco Firepower devices? Does Firepower support CISCO-NAT-EXT-MIB for NAT or is there a firepower specific mib to find NAT related metrics?Thanks in advance!
Hi,I found the CISCO-IPSEC-FLOW-MONITOR-MIB that contains OIDs to monitor params like Local Peer IP, Remote Peer IP, Tunnel Status, Encryption Algo etc. for Site to Site VPN. Also, CISCO-REMOTE-ACCESS-MONITOR-MIB that contains OIDs to monitor params ...
Resolved! Two Firewall in Different Locations
I have 2 firewalls in different locations (FW1 in City 1, FW2 in City 2). I also have 1 FMC located in City 1. How can I configure FW2 in City 2 if my FMC is in City 1?
High-severity vulnerability CVE-2025-20111 is related to Nexus 9k standalone mode and could allow an unauthenticated, adjacent attacker to cause the device to reload unexpectedly, resulting in a denial-of-service (DoS) condition. This vulnerability i...
Hi All, I heard that there is a 90 day evaluation copy of FTD you can get from Cisco. But look like when I tried to access Demo License Section with my Cisco ID it is giving some error related to my id is not associated with required service contr...
Does anyone know if there are any functionality limitations on the lower-end FPR models like the fpr1010? I have a client that is looking to replace 5516's at their main site and DR site with fpr1140s. But it's occurred to us that since the DR is alm...
Good Evening... We are running ASA 5545X with 9.14(1) / 7.14(1). I am wondering if there is a CLI command to see the local password expiration in days?? Like showing the number of days left before the password expires. I understand in ASDM I can view...
Hello, I'm unable to clear health alert "Interface Status" in FMC ver 7.2.5 after enable a pair of subinterfaces in the FTD. The detail of error is: Interface 'Ethernet1/6.250' is not receiving any packetsInterface 'Ethernet1/6.250' has no linkInterf...
Trying to deploy both Web-Cache and HTTPS 443 WCCP to an FTD. I can get the 443 tunnel up, but not the Web-Cache, the deploy fails.Lina messages FMC >> clear session FMC_SESSION_1 accessMain-3120-SFW >> info : WARNING: This might result in parallel a...
Resolved! Bidirectional ASA ACL to FTD ACP
One of the things discovered with the Migration tool is it assumes the Inbound for an interface is default and only recognizes outbound. I have 3 DMZ interfaces that I control traffic from servers inside the DMZ to have access to other interfaces an...
7.6.0 is listed as both affected and fixed. Please can this be confirmed which is correct?
