Hello, I'm deploying an FTD v6.6.5 created as native device in a Firepower 4110 appliance as replacement for an ASA5585 with Firepower Services, I have already added the FTD to the FMCv (v6.6.5) and migrated the ASA configuration using the Cisco Migr...
Forum Posts
Resolved! Unable to add FTD into FMC
Hello, I am currently unable to add FTD into FMC, each attempt it comes out with error message host x.x.x.x is not reachable. - FMC in Europe, FTD in China.- The FMC ping successfully FTD and vice versa.- I did configure network management-data-inte...
Hi All,I have a FirePower with FMC and web filtering license.I have enabled the URL filtering in the security intelligence with blocking all categories.Is that good enough?Can it perform URL filtering on https?Is SSL decryption needed for url filteri...
Hi ,I would like to delete ASA temporary selfsign cert and use our organization cert.Now asa management portal using ASA temporary selfsign cert .I would like to change this asa temporary selfsign cert with our organization cert.so let me know how to...
Hi,FMC won't let me delete a FTD device that have a L2L VPN tunnel configured. I am getting the following error, if I try. The Device 'FTD01' cannot be deleted because the following VPN Configuration(s) refer this device.Site to Site : LAB_l2LPlease ...
We can into a strange problem. As above, it's a simple S2S VPN tunnel. On our side, Node1 is primary, Node2 is secondary but connection is always established through cluster IP. There was a failover, so Node2 is primary and Node 1 is secondary. Im...
Hii have 2 FTD 4120 with cluster togethermy problem :users connections (ssh) become disconnect after a timebefore , i have this problem on ASA , and i solve it with this command " timeout conn 09:00:00" for example ,, i increase default time.where...
Hello, Earlier FMC 6.6.4 allowed to enable or disable multiple columns in one go to customize the ACP rule window view but FMC 7.0 will not allow you to have that privilege, once you uncheck any of the given options the menu will just disappear but ...
Resolved! FTD VPN Question
HiShould traffic crossing Internet via a VPN be Translated,?? Thanks
Resolved! FMC and LDAP integration specification
LDAP integration works, but!!! My FMC operates on VMWare in a management network.I have an inside network with windows domain controllers.Hence the FMC is not able to connect with the domain controllers.This gives a lot of pain to specify the AD Real...
Hi,I am planning to upgrade a FMC 2500 appliance from 6.6.4 to 7.0 but I want to check first if I need to upgrade the Bios.I couldn’t find anything in the release notes, so does anyone know where I can find this information?Thanks/Chess
helloi have 2 FTD 4120 (cluster together)i want to upgrade them ( FMC and FTD )to 6.6.5 (stable version) but i dont know upgrade path for iti should not have any timeout for this procedureFTD version 6.2.3FXOS version fxos-k9.2.4.1.222FMC virtual 6...
Dear All, I am trying to make a policy based IPsec tunnel with remote partner and below is the configuration. Do I need to configure the access-list inside and outside or I can skip them? crypto map IPSEC_map 80 match address ABCcrypto map IPSEC_map ...
Resolved! Firepower - hairpin/reflected NAT rule
Hi Everyone, On the FTD 2110 running the newest recommended software (6.6.5-81) we have to interfaces on the inside (internal + dmz) and outside one. In dmz there is a service that is exposed to the internet (NAT to the public IP that is with the sam...
Hello, I need to change the SITE ID on the Firepower Cluster information, by doing so will it restart the chassis or virtual ftd's ?
