I'm sure you all are familiar with the CIS controls. We've had a couple issues tied with (I think) one of the changes, and one we can't get resolved. I believe the issue comes from "password encryption aes." We initially deployed the changes to 3 fir...
Forum Posts
Resolved! Cisco Firepower 4140 Twinax support
Dear Community, Does the Cisco Firepower 4100 series ( or any other chassis for that matter), support the following: -SFP-H10GB-CUM3-SFP-H10GB-CU7M-AO-SFP-H10GB-ACU10M According to this link I believe it does, but wanted to be sure. https://www.cisco...
We have a Cisco firewall that can be accessed through the web interface called Firepower. I discovered that there is a geolocation rule that blocks visitors from South Africa. The issue is that we recently got a student from there that cannot visit ...
Hi, The Pix 501 that has been in place for quite some time acting as a firewall between two LANs LANA - ip address outside 192.168.45.241 255.255.255.0LANB - ip address inside 192.168.44.240 255.255.255.0 This config has worked ok as devices in each ...
Hi everyone. I planing to migrate my Prefilter rules to ACP, the only reason I'm not doing yet that work is because actually have 700 line of rules.. Is any way to migrate prefilter to ACP using some script ? Regards.
Hi there,i have configured cisco asa firewall properly and configured http server and IP's as well properly,but when i am trying to access the url in browser to install the asdm its not opening this url ... the error is attached.also i am pasting the...
Someone else had setup the AD user account for our realm in FMC. Does the user need to be set as a domain admin or can it be a normal user account? I'd think that it doesn't need to be a domain admin, but, wanted to get some guidance. Thanks!
Hey guys, we have an ASA 5525 as our AnyConnect VPN concentrator. We get messages like the below in our log files, we are then sending to SolarWinds. I have alerts setup in solarwinds to email me when this happens. However is there a way to view or s...
Hi Folks,I'm trying to find out some really basic information about the Firepower 1010. It seems like most of the information is all about more sophisticated, high-powered stuff. FTD vs ASA--which to use?I think I finally get that unless you use the ...
How to List all sensors managed from FMC though FMC CLI.
Having issues with ISE on vmware. This is for small lab at home. I can get ISE installed on my vmware ESX machine at home, it has 16 gigabytes of ram. And it seems ok with disk speed and such. It’s a pretty fast VM (all SSD disk) and there is no...
FirePower Newbie: I have a pair of FP 2110's in an HA configuration. I fail-over to my secondary the other day and hours afterwards, I had reports of dropped RDP, SSH, and Telnet sessions throughout my network. I failed back to the Primary and all is...
Hello Team, We have ASA5525, without IPS enabled, it is used mainly for anyconnect VPN.. and we are suspecting hitting of malicious traffic on VPN from outside.How we can block this on outside interface if i know the malicious traffic source IP. Any ...
Hello!Dear colleagues, I need your advice about ASDM sessions on Cisco ASA 5585-X.As I understand, Cisco ASA 5585-X has a limitation, that allows only 5 concurrent user sessions.But if 5 people use it and someone forgot to close it, new users can't l...
So, in this particular configuration, I have an ASA connected to a cable modem, providing me a single static IP.Cable modem gateway - 1.1.1.2 /30ASA interface "outside" - 1.1.1.1 /30I have a DMZ setup, with a single device in it:ASA interface "dmz" -...
