Hello, I would like to know what he process is for upgrading a site in FTD from a 5506x to a larger appliance. We're planning to add more bandwidth and will likely need more capable hardware. I'm hoping I can just migrate my settings to the new dev...
Forum Posts
I have configured a cisco firewall asa(in packet tracer) to allow only modbus tcp port 502 to go though the firewall from 4 inside client (172.16.0.1-172.16.0.4) to outside server by writing acl and then auto natting.Is this configuration correct??...
Resolved! ASA5506 New VLAN for Guest WIFI
HelloI need to create new VLAN02 for guest WIFI and set up some rules to restrict access to some IP address.My ASA5506 is in BVI mode.The current ASA interfaces are like this;BVI1 – insideGIG1/1 - outside -GIG1/2 - inside_1 -GIG1/3 - inside_2 -GIG...
Team,I am struggling while configuring ASDM with my cisco firepower 2130 firewall it is on ASA mod. My firewall is on 10.1.2.0 subnet and I am setting in the subnet which is 10.1.57.0 right now I am unable to access my firewall which IP addresses are...
Hi, While I was upgrading FirePOWER from 5.4.1 to 6.0.0 there was a power outage, and the upgrade didn't complete. The module became unresponsive (it's status from ASA CLI) until I had to shut it down, reset it, then reload it. Now I can access ...
while sending a file to particular target, if the file size more than 250 KB. The firepower is blocking. I found a similar type of bug CSCva18960, suggested workaround is to disable the preprocessor rule for that particular traffic and I did the same...
I get this message now when I add a new user for in the local CA server. Is Cisco removing the local CA server completely from the 5506-X?? WHY?
Hello, What command would I run on an ASA to show the encryption domain(s)? Regards Troy
My Cisco Firepower 2110 crashed in the middle of a deployment. After it came up I cannot define my SIte-Site VPN. I get the error message "ERROR: Group Policy |s2sGP|<ip removed> already exists. ERROR: Failed to add group-policy |s2sGP|<ip removed>"....
Hello everyone I have the Call manager 10.5.2 and I am really concerned on how to install security agent into the system to Identify the vulnerability if exist.and what is the platform of the system and how can i know it exactly so i can install the ...
Hi All, We're looking to make a change to the intrusion policy setup we use on a deployment, currently we have a single 'master' intrusion policy that we apply to all of our access policy rules. What we're looking to do is have a separate policy just...
Is this normal to see after a boot of the 5512-X ? It is the very last message I am seeing on the console following boot of a brand new unit.Warning: partition table exists on the storage device (sn: XXXXXXXXXX)but may be lost or meaningless after c...
Has anyone configured IPSec tunnel with Symantec WSS (web security service in cloud) on ASA or Firepower? We need to send ports 80, 443 traffic for destination IP’s 0.0.0.0/0 (i.e. internet) through VPN tunnel to Symantec cloud. Other ports traffic t...
Hi.I have a problem with RA VPN DHCP configuration. VPN users get IP address from the local pool just fine, but when I try to use my Windows Server 2012 R2 DHCP server, i get the following errors and it always falls back to local pool: IPAA: Session=...
I have a ASR1001 that I upgraded IOS to asr1001-universalk9.03.07.06.S.152-4.S6.bin and now can not get an interface to come up. Shut No Shut does not help. Do I need a license for the interface? I'm using a GLCTE in G0/0/0 License Store: Primary Lic...
