Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi, I have FMC1000 appliance which running on version 6.3. I would like to verify hardware infomation of the FMC via CLI such as NIC, CPU cores, Memory, Event storage space and power supply status. Unfortunately, I have found only "show version" to e...

20190819_131951.jpg
jumperdub by • Level 1
  • 9487 Views
  • 1 replies
  • 0 Helpful votes

Hi all, I have a 4110 cluster which I am trying to troubleshoot a load balancing issue. Two commands that I see frequently applied to CCL and CDL port-channels are: ! int po1 desc CDL port-channel load-balance src-dst ip-l4port port-channel span-clus...

Seb Rupik by • VIP Alumni
  • 3345 Views
  • 4 replies
  • 0 Helpful votes

Hi New to using  Cisco ACL's, I have an ASA 5510 (Cisco Adaptive Security Appliance Software Version 9.1(7)13 ) I have nat'd subnets on Ethernet0/1 & Ethernet0/3, security-level 100 and these work correctly. I have a sub interface, Ethernet0/1.1 (vla...

Sherdy by • Frequent Visitor
  • 1846 Views
  • 1 replies
  • 0 Helpful votes

HelloWe 're going to buy 4 fpr9k-sm56-ftd-bun appliance and we want to install FTD image on it (not ASA image).We want to know how many contract (CON-SNT-FPR9KSUP, CON-SNT-PR9KSM6F, CON-SNT-FPRC93AC) we should buy? Do we have to buy 4 contract(one co...

MKH by • Level 3
  • 2638 Views
  • 2 replies
  • 0 Helpful votes

Greetings!I recently picked up a Pix 501, and Im trying to configure it for use within a small network. The inbound internet is coming via a combo modem/router, which is connected to eth0 on the pix, but Im experiencing some configuration issues. Im ...

Hi all - I have "inherited" some items that look like they need to be upgraded. I've read through the upgrade guides, etc but wanted to make sure I am not missing anything. I need to get my virtual FMC from 6.0.1 -> 6.1.0 -> 6.4.0 Can I perform this ...

samw by • Visitor
  • 1426 Views
  • 1 replies
  • 0 Helpful votes

Hello all, We have an SFTP server that as of late, has become a target of frequent SSH/SFTP brute force login attempts, though, often I just see non stop connects and disconnects over the period of a couple of hours.  We are using an ASA 5516X with F...

MauryJ by • Level 3
  • 3766 Views
  • 2 replies
  • 0 Helpful votes

I'm running FMC 6.2.3.14 on 18 ASA devices.I have disabled SIP inspection on my ASA devices, but how do I do this in the firepower policies?I'm assuming the sfr policy on the asa routes all traffic through the firepower module, which means that firep...

Lee Dress by • Level 5
  • 12282 Views
  • 4 replies
  • 0 Helpful votes

HI,Basically we have two ASA 5525 version 9.9.2 with SFR Module version 6.2.13, So i need to Install the FMC on vmware EXSI, for centralised management and need to confirm that what will be the procedure to install and configure the FMC on vmware EXS...

Hello, Does anyone know if the ASDM is handeled differently/automatically when deploying an ASA image onto a available Security Module on a Cisco 9300 chassi? The only ASDM file that is showing locally (dir) is "asdm.bin" without any version number i...

andmo5 by • Community Member
  • 1032 Views
  • 1 replies
  • 0 Helpful votes

ASA5525 stopped responsive and was not accessible via ASDM, although it was accessible via SSH. And the issue was resolved after reloading the ASA.  We noticed after reload there are numerous  ‘FSCK0001.REC’, ‘FSCK0002.REC’ files etc on the flashcard...

Tuba by • Cisco Employee
  • 1306 Views
  • 3 replies
  • 0 Helpful votes

Hi there,We're running FMC v6.3.04(44) with Geolocation update 2019-07-18-003. We have noticed that some IP addresses get identified by FMC as originating from the US, but many other online sources when queried for the same IP address show the addres...

Review Cisco Networking for a $25 gift card