I recently purchased a Cisco ASA-SSM-AIP-20-K9 AIP Security Advanced Services Module from eBay and installed it into my Cisco ASA5540 firewall. It is shown properly, using the "show inv" command. I just need help in figuring out how to install the ...
I am replacing my SonicWall with FMC(6.3.0.3)/FTD 2110's (6.2.3.13). And trying to configure a "transparent mode" interface. I am in Routed mode, 1/1 is my WAN (192.1.1.1/24), I'd like interface 1/8 to be in transparent mode DMZ, so I don't have to w...
Hi All,My company has purchased Firepower 2100 series firewall with ASA image 9.10.1. My query is related to CLI and GUI. Is it the CLI Commands and GUI steps/view will be same as normal ASA and manage by ASDM. Any help will be appreciated
Trying to determine how to properly configure FQDNs in access lists on an ASA5525 to always resolve for HTTPS from an internal network server VM application reaching out to them regardless of what ip address changes occur to each domain name over tim...
Hi All, We have a HA Failover pair of Firewalls at different Data centers - A link is there in between where they are forming HA. Somehow we have lost management access to those firewalls now. Can someone please advice how we can break the passwork ...
using FDM to configure the FTD, dont see any option where i can configure SNMP. do i need to use Flexconfig to configure snmp. I'm using data interface to manage the device. Management interface not in use.
Im trying to login to my Defense Center thru the WebUI, I'm able to do so but after a few seconds it logs me off What could be cause this issue?
Hi Techguys,i want to confirm the VRF Support in Cisco Firpower 2130. I have requirement for different connections from Partnet. I want to keep all partner information separate. i want to keep voice, Internet and Partners VPN in a seprate VRF. Pleas...
I have a bunch of ASA's which I want to backup.My goal is to use the "backup" command with a SCP location:"backup /noconfirm location scp://<username>:<password>@<SCP-server-IP>/" The backup is performed, and a SCP session and filecopy is started (ac...
Hi everyone, I hope someone can help me out here. I have an IPSec tunnel set up between a Palo Alto and Cisco ASA. The tunnel is up and running and is passing LAN/WAN traffic. So far so good. On Thursday, the users on site were migrated to Office 365...
I have a firepower 1010 I am trying to configure for a customer. It is going in place of a router that is there now. internal ip for example on firepower is 192.168.1.10 and this is the default gateway for all computers then we have another router ...
I am unable to update my ISR 4331 IOS-XE 16.6.4 Snort IPS signature from the base 29.0.C. I have also tried the latest signature (UTD-STD-SIGNATURE-2983-71-S.pkg) and receive the same error message. No issues contacting the HTTP server and copying ...
I have an issue with a VPN between an ASA 5515 (9.1(7)29) and a Fortigate 501E (5.6.8). We have the Cisco ASA and the customer has the Fortigate. Both are configured to have an L2L VPN between them. The VPN is up and we see traffic being encrypted an...
im shifting a new fmc+ftd instead of an old asa firewall , i was wondering after i shift the new fmc+ftd with the same inside and outside ip addresses if i need to clear arp my layer 3 core switch and my isp router?
For the life of me, I can't figure out what is causing my NAT problem. I ran a packet trace from 10.0.0.1 to 8.8.8.8 and received "(nat-xlate-failed)NAT failed" message. All I'm trying to do is to allow any host from 10.1.1.5 subnet to go out to the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-10-2026 08:58 AM | ||
| 08-10-2026 02:48 AM | ||
| 07-22-2026 05:00 AM | ||
| 07-16-2026 06:39 AM | ||
| 07-15-2026 08:48 AM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
