Dear Community,Do you know if 4461 ISR SFP+/10 Gigabit Ethernet port (TE 0/0/4) accept 1G SFP? Thanks,Gabor
Dear Community,Do you know if 4461 ISR SFP+/10 Gigabit Ethernet port (TE 0/0/4) accept 1G SFP? Thanks,Gabor
Good day,I have a Cisco 9300L-24T-4X switch. It has 4 x10G uplinks. I wanted to link it to a host with a 10G baseT gbic transceiver. I purchased a Cisco SFP10G-T-X transceiver. But the switch gives an error of "The inserted SFP module with interface ...
I'm looking for compatibility information on this part number. It's not listed under Cisco TMG. Thank you.
Hello, I have a customer that purchased a 9300 series switch and a 9300x series switch with the intention of stacking the switches before I explained to them that they are not compatible. So now they want to use 10G SFP's in a LAG to connect the swit...
Hi all, Strange problem i have a ASR1001-X with GLC-LH-SMD not coming up, the GLC-LH-SMD are seen by the ASR but the link stays downbut with GLC-SX-MM's installed the link comes up and is finei have tested the LH's in other devices and they are fine ...
I have a Cisco 9200L-48P-4X switch connected to a Cisco 3850-24X switch via 10Gb SFP modules. The modules are LRM which I am using mode conditioning patch cables on both ends to condition the light for about 120ft of OM1 fiber. I am using two of th...
Hello , why i dont see all the interfaces when usinf # sh int status ,like for example the TenG interfaces and the sfp slots ,here is the output of # sh int summaryGigabitEthernet1/0/20 0 0 0 0 0 0 0 0 0GigabitEthernet1/0/21 0 0 0 0 0 0 0 0 0GigabitE...
Hi,The GLC-SX-MMD is supported or compatible with Cisco 9400 series switches. (Cisco-Lc24S) ?
Hi all,my problem is a swaying latency on the connection between two 4507 switches. On 4507 is an vss-construct the other one is connected two both chassis. At the moment one of the two links is down for troubleshooting purposes.When I send a ping to...
Hi all! I have an error with the 100GE link between A9K and NCS2K using CPAK-100G-SR10s and a MPO cable. At A9K's side, the RX value of all lanes is fine as below: but PCS lane mapping of all lanes is invalided and of course, that port is not UP. A...
Hello I'm getting frustrated, I've now ordered 2 cables and I can't connect to Cisco via Putty with either of them. Which cable do I need to connect me via Cisco ?I tried with this cable but putty shows me a black window. Cable Adapter 2With this Ada...
Dear Experts,I'm looking to connect my two window PCs with an optical networking card (PCIe card) using fibre optics cable and I wish to achieve a 100gbps data rate. The wavelength I'm looking at is single lambda (~1550nm) possibility QSFP28. Can any...
Hi Everyone,I have a NCS2006 and need to monitoring power supply status via SNMP.I use SNMP Object Navigator to find power supply oid to set SNMP monitor on my NMS.But some similar oid like 1.3.6.1.4.1.9.5.1.2.4 (chassisPs1Status) or 1.3.6.1.4.1.9.9....
Does anyone know if the Cisco Nexus 93240YC-FX2 support RJ-45 Transceivers (1G) for either uplink or downlink ports? I tried looking this up on the Transceiver Module (TMG) Compatibility Matrix, but it wasn't very clear. Thanks.
I need to know the differences of SFP modules sold on amazon in the name of cisco and official cisco module sold by cisco via partner. Comparing to original the modules in amazon has very less amount. So, please clarify what can i go.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-25-2024 01:25 PM | ||
05-05-2024 05:19 AM | ||
03-27-2024 12:16 AM | ||
03-27-2024 12:09 AM | ||
09-10-2023 08:07 AM |