Folks, I've done this before, but for the life of me I can't find the registry key used to turn off logger and cicm recovery...I remember it as a /norecovery entry in a registry key, but not the actual key. Any help would be greatly appreciated.
Folks, I've done this before, but for the life of me I can't find the registry key used to turn off logger and cicm recovery...I remember it as a /norecovery entry in a registry key, but not the actual key. Any help would be greatly appreciated.
Is it posible to make some VIP numbers, to special process (special Ring or transfer). If no, may be it planing to do in future?
Hi guys,This may sound a little weird but I am trying to unregister an FXO port from CCM. I still want the gateway to be registered but currently I do not have a line connected to that port. For troubleshooting purposes, I'd like to un-register th...
I need some guidance in acquiring some tools that will help me test/simulate VoIP scenarios and high loads of calls. The solution should support both h323 and SIP protocols if possible. I am looking to automate some VoIP tests.Any references will be ...
I need some guidance in acquiring some tools that will help me test/simulate VoIP scenarios and high loads of calls. The solution should support both h323 and SIP protocols if possible. I am looking to automate some VoIP tests.Any references will be ...
Hi, I have ordered a cisco call manager and some ip phones without the license.I have also ordered the license but not together the phones.Now, I want to know if it's possible to do the installation and make it up and running even if the license wil...
The other day, I used BulkEdit to change everyone's MWI extension to an "X". It worked fine for an entire day. I come in this morning and all the extensions are blank and "use MWI for message notification" is unchecked! This is for EVERYONE in Unity....
I have set up extension mobility in CM 3.2. When I use the login service and input my username and PIN I get the error message "Proxy Not Allowed". Has anyone else experienced this issue?
I can access the saweb from any other version of IE except mine. I recently installed the latest patch for it and now it doesn't work. newly applied q323759 already applied (q319182,q321232)Anyone else have this problem? Know how to fix besides uni...
we have a remote site that gets dial tone from a cluster across the wan. the rmote site has srst running on a 3620. when the primary call manager gets rebooted the phones register to the router with srst rather than to the secondary call manager. how...
Can someone shed some light on this type of integration. Also i was looking for a list of tested/certified CCM integrations with the Intuity ...
Hi,does anybody know a good (cheap?) software to meter QoS criterias (delay, throughput, packetloss, jitter)?Alex
Hi, does anybody can help me?I have a CallManager cluster (three CallManager ver. 3.1(4b)) with two locations, it seems that some time the aviable bandwith is NOT released after call completion, so the location's aviable bandwith becomes slowly zero ...
I recently installed Unity 3.1(3) on a 7750. I created a handful of users just to make sure everything was working properly prior to creating 350+ of the clients users. I ran dbWalker ( the latest version from AnswerMonkey ) and came across a few ...
I recently upgraded my call managers from 3.1(3a) to 3.1(4b).3.1(4b) installed a new Phone load "P00303010405" and when the phones upgrade to the new firmare the upgrade processes is taking about 15min per phone. Is this normal?? I have upgraded th...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-28-2025 02:36 PM | ||
04-19-2025 04:07 AM | ||
04-02-2025 09:00 AM | ||
03-22-2025 10:34 AM | ||
03-17-2025 03:19 AM |