I used AXL SQL Toolkit with sample.xml input to generate sample.response file with needed data. How now I can open created file with readable view? Thanks
I used AXL SQL Toolkit with sample.xml input to generate sample.response file with needed data. How now I can open created file with readable view? Thanks
Hello,I have a network with 1760 voice router. These are gateways to the pstn network. I have to upgrade the IOS to support SG3 fax speed. With the software advisor I found the one software: 12.4(15)T7 that supports this feature.Now I have periodical...
We are using the CM 4.1 and Unity 4.2, but they didn't integrate with AD. Now we want to integrate the CM and Outlook so that the user can make the call from Outlook Contacts. Should I have to integrate the CM with AD first? Any documents can show me...
Hi expert, We have installed Cisco call manager version 4.0 and it has beenconfigured for two groups to facilitate local calls and IDD calls both. So now wehave a problem of applying a security code for IDD calls to prevent unnecessaryIDD calls be...
Hey All,We upgraded the IP phones to sccp41.8-4-1sr1s from SCCP41.8-2-1S, and now dialing from the corporate directory does not work.We just get "the call can not be completed as dialed"But it works ok from the old firmware phone.Has anyone experienc...
Is is possible to live stream video, and live chat during the stream, through my video portal 4.1? I'm having a tough time finding out if it's even possible and how to set it up if it is. I hope I've posted in the proper area. Thanks in advance.
I am just starting out and have a UC500 to learn on. I am trying to connect to my ISP using PPPoE through an Alcatel Speedtouch Home DSL modem in relay mode, but when I try to configure the UC500 from the GUI ...the PPPoE settings are greyed out. Can...
how do i increase the number of users for meet me conferances
Have 2851H323IOS SPservices 12.4.15TSee attached config.During WAN outage SRST works fine. Calls can be made outbound but calls cannot be made inbound.When main number called gateway picks uup the call in 1 ring and the caller hears dead silence the ...
For outbound calls, I would like to send out the calling number (DID number) to the carrier so that they can track all outbound calls that originate from the Call Manager. I have found a Clusterwide Parameter setting "Calling Party Number Screening I...
Can the Unity visual voicemail service called Phone View, be accessed from the IP Phone Services button. If so, what is the Service URL?
I have a 3560 switch that has been defined under Phone Tracking>LAN Switch Details section of CER. I had a bad DNS entry pointing two different switch hostnames to the same IP address. I made the correction in DNS to point to the correct switch. C...
Hi The red light doesn't flash on our 7941 and 7961 after a missing call come or leave a voice message. Does anyone could show me how to troubleshoot or should I configure anything on CUCM and Unity? CUCM version: 4.1IP phone firmware: SCCP41.8-3-3ST...
Does Cisco 7937 support more than 3 party conference?If yes then how to do it.Thanks & Best RegardsDeepinder Singh
helloi hearded somewhere that if you full all PoE ports on a switch with 7911G phones, there are resets very often. because i address the some problem with the specific ip phones on poe switches, does anybody know if there is any solution. Maybe a fi...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-28-2025 02:36 PM | ||
04-19-2025 04:07 AM | ||
04-02-2025 09:00 AM | ||
03-30-2025 11:51 PM | ||
03-22-2025 10:34 AM |