Ask Me Anything Event Thank you for joining us for the Expert Insights Series on ACI & NDI: Empowering Data Center Excellence! Our Customer Success Specialists Cody Albea, Peter Nalley and Manuel Valasco will be available from May 15, 2025 throug...
Forum Posts
Hi, I have this X2-10GB-SR on a cigesm switch port Te is used as uplink yet i now see the X2-10GB-SR LED status as amber and the port goes to err-disable. Is the X2-10GB-SR faulty? Thanks Nyi
Resolved! New Feature in NX-OS 7.0(3)I7(2)
Hello,Can anybody confirm that I understand good the next lines: "Beginning with Cisco NX-OS Release 7.0(3)I7(2), the Multi-Site border gateway allows the co-existence of Multi-Site extensions (Layer 2 unicast/multicast and Layer 3 unicast) as well ...
Resolved! ENCS-5408 (default-gw for mgmt & wan)
I have a "NFVIS" ENCS-5408 router whose WAN port is connected via /30 address. Now, this device doesn't seem as intuitive as regular IOS where I set default route for different networks. How do I set different default-gw so that both mgmt and wan r...
Anyone know about xbar log ? I found xbar status powered-dn on Nexus7710 after turn-on this log below. switch# 2015 Jun 16 00:44:34 switch %$ VDC-1 %$ %XBAR-2-XBM_EEM_FABRIC_ACTION: Fabric slot 3 has been reloaded by xbar-manager because of an eem-...
Hello, we have purchased for our datacenter two new Cisco ASR1001-X. On both of them the TenGigabitEthernet interfaces have no coniguration [1] , no SFPs and no cables connected. In both of them we see errors (input, CRC) [2] on TenGigabitEthernet ...
Hello,so i just finished to install two hyperflex clusters using the 2.6 data platform installer.Everything went right, cluster deployed and configured but for some reason i cannot login into the HyperFlex Connect GUI.When i try to connect i receive ...
Hi,I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and...
Please excuse my lack of knowledge as I am at a beginner level of Cisco knowledge at best. My company has recently purchased Cisco Prime Infrastructure and has tasked me with configuring all of our Cisco devices on it. While I was able to get Prime...
Hi there, I am having trouble testing a new back-to-back vPC setup. I have two vPC domains connected: 1a(pri) <--> 2a (pri) 1b(sec) <--> 2a (sec) I have setup some continous pings behind vPC's connected to classical etherchannel switches....
Hi, I need to implement DHCP relay in DC environment. I am attaching DC network diagram. There are total 3 Vlan in one VRF (name: SAP_HANA). Three vlan subnets are mentioned below. VRF: SAP_HANA Vlan10: 172.16.10.0/24 Vlan11: 172.16.11.0/24 Vlan12: ...
Hi All, I installed a N9kV switch for vxlan testing, Requested License from Cisco licensing team and they provided me a demo license for about 60 days. At some point I reloaded the nexus switch it boots up with a new serial number and I lost my lic...
Dear Members, Can anybody assist to configuration sample of vrf route leaking between default vrf and non-default vrf with MPLS and MPLS VPN enabled? I have a use case whereby network managing server resides in a vrf and the NMS has to have reach...
Hello, I have doubt in nexus. How can we confirm that following command has been enabled on nexus switches or not. I searched online but could not find an answer. , Do we need to enable feature called privilege to do so? Service password encrypti...
Hello All, We are working on N3132Q-XL Switch which is 32 port fixed 40 Gigabit Ethernet QSFP+ ports switch We want to add SFP-10G-SR-S; 10 quantity in the switch but its giving me error if i try to add more than 8 in CCW tool... i want to confirm ...
Hi, i m having an issue that, when i swap the new 4200watt power supply to replace the old 2800watt psu, there's an err disable happend, and some of my Ap only getting 16watt of power instead of 32. A little urgent on this, haha. Apologize for my...
