We are looking at using VMPS for VLAN membership. Has anyone had any experience with this, and if so was it good/bad/so-so. Am looking for suggestions.Thanks in advance for helping the hopeless.Dave
Can anyone please tell me if the 2801 with the following IOS allows configuration for BGP or do I require a feature set upgrade - If so, which one?Cisco IOS Software, 2801 Software (C2801-IPBASE-M), Version 12.3(8)T6, RELEASE SThanks in advance
Hi, all...I have a CSS load balancer set up to load balance a pair of DNS servers running bind on RedHat. The keepalive script provided, ap-kal-dns, only checks to determine if named is up and running on the DNS servers. On the DNS servers, though,...
I am new to this so bear with me. Inside my network I have servers using public addresses and I use private addresses for my pcs, and devices on both nets communicate amongst themselves. I need to add a route to my router attached to the internet s...
How to configure point to point leased line using frame relay? I did configure both side router with frame relay, configured the subinterface for point to point. I can not connect to other site. I don't have any info on DLCI, service provider is supp...
Hello,I have a MC3810 that don't boot, it is possible that the eprom ios got dissapear and without it he don't boot?i change the ram, the flash, i don't see anything that i can change to test :-)Ciprian
Does the catalyst 4500 with sup 4 support Reflexive Access?I get the following when trying to use this old command:C4K_IOSINTF-4-REFLEXIVEACLNOTSUPPORTEDIOS rel is 12.1(20)EW2
3550 switch Switch Name - Switch1 Vlan 2 - IP address 172.17.0.1 255.255.224.0 Vlan 3 - IP address 172.22.0.0 255.255.224.0 UP Link Port IP address -172.23.0.21 255.255.255.252 3550 switch Switch Name - Switch2 Vlan 4 - IP addres s172.17.32.1 255.255...
Hi,One of Customer is using Cisco 7513 having PA-8E Module installed in it. We have 8 E1's. Router is running with 12.0 25 S1. We have configured Multilink on Router. The another end is having Juniper Router. When we use multilink with 3 E1's, it wil...
I have a 6509 with sup720. It has two Fe connections to two AT&T managed routers which in turn have 2 E1 ccts into our their MPLS VPN hetwork. The managed routers load balance on inbound.I want to load balance on these 2 ccts as the packets leave the...
I have CISCO 3640 it connected with 4 WAN Frame Relay connections to my branches .. I have 1 new connection but the connection type is different (ie. MPLS or Leased Line).. is it possible for me to that different connection type (MPLS or Leased Line)...
A long time ago, an IT associate of mine built what i think was equivalent to an ethernet crossover cable so that he could link up two serial interfaces configured with Frame Relay in a lab. I think he had to either 1)implement or 2) shut off "frame...
Hello, I have one L3 Cat. 3550 Switch. Currently, I configed Inter-Vlan Routing and create two VLANs( VLAN 50,60) on the switch. - VLAN50: 192.168.1.1/24 - VLAN60: 172.16.1.1/24 The clients on both vlans can access each other. The que...
Hi,If I have a LAN with 2 routers to access it. On each of those routers I use OSPF and route summarization (summarizing the LAN network addresses). How will redundancy work in case the active router looses the path to only one part of the LAN (Since...
