I have Catalyst 3550 with the following config (disregard policy names since I am experimenting):mls qos aggregate-policer pol_1Mbps 512000 8000 exceed-action dropmls qospolicy-map 1Mbps class 1Mbps police aggregate pol_1Mbpsinterface FastEtherne...
This is strange. I'm trying to tftp the image to a 6500 MSM (its the first generation layer3 blade for a 6500, the predecessor to the MSFC) and am unable to. There are 7 of them and they all show the same symptoms.When transferring image to flash f...
the cam aging time for vlan 1 keeps getting reset to 15 I have enabled portfast on all host ports across my enviroment. I still have many hosts in VLAN 1. I have some servers in VLAN 900. These servers become unaccessible to some of the clients ...
I have a reqmt say I need to block my people accessing www.cisco.com. I tried it with class map and Policy map selecting HTTP URL cisco.com and I found the same not working. But with the same config,if I give any specific link in cisco.com say /go/ip...
IOS running is 12.1(23)E2 .Feb 1 10:24:25: %OIR-SP-3-PWRCYCLE: Card in module 6, is being power-cycled off (Module not responding to Keep Alive polling)Feb 1 10:24:25: %C6KPWR-SP-4-DISABLED: power to module in slot 6 set off (Module not responding to...
I’m not sure where I should begin looking for any solutions that may be out there.My public DNS is currently being handled by Qwest and I am getting ready to change to a different service provider. At the present time I also use a Qwest managed fire...
I have about 300 users going through a Cisco 2801 router with IOS Firewall to get to the internet. All of these users have to go through a proxy server to get to the internet and that server sits on the other side of the T1 from this router. So, I ha...
Hi all,could someone recommend me or give me some experiencewith configuring ACL on VLANs.I have concrete question as well. Could I usereflexive ACLs and ACLs with word established in ACL lines.?Thanks a lot.jl
The router is running IOS 12.0(7)XK3 - the link is currently autonegotiate - i plan to change to manual full duplex 100Mb unless anyone can advise another course of action? Dropping 4-5 % of packets between the 3640 and the 4507 - Is it a conflict wi...
Hi ,I would like to confirm that this behaviour on my 2940 is correct. I have a vtp server configured that is advertising about 10 vlans to the vtp clients of which the 2940 switch is one of these. What I see is that the trunk interface to my vtp ser...
Hi!We currently have a WAN set up in the manner depicted in the attached diagram. For traffic between the 2 sites, we have designed it such that the private MPLS link will be the preferred route, by adding static routes into the each site's main rout...
I am configuring microflow policing on a 6509 with Sup2, PFC2, and CatOS 7.3.1. It works with an ICMP ACE, but not with IP or TCP. Aggregate policing works fine with IP or TCP using port or vlan base QOS. The config is basically the same for microflo...
Hi,I'm trying to configure channelized E1 on Cisco 2621 with 12.1T IOS version.controller E1 0/2E1 0/2 is down. Applique type is Channelized E1 - balanced Far End Block Errors Detected Receiver has loss of signal. Version info Firmware: 20000306,...
Hi All,We have a series of Apple Mac computers and a few Apple Mac servers, connected to our network. The network is comprised of 3524 and 3548 series Catalyst switches.This all works fine during regular operation, however if a file or number of file...
Application: Microsoft Netmeeting used for sharing the desktop, file transfer and Audio/Videoconferencing using the Webcam. Minimum 2 workstations are required with Netmeeting running on them. If you want to videoconference, webcam is attached to the...
