Does it HSRP balancing of traffic?Is there any documentation about the subject?
Does it HSRP balancing of traffic?Is there any documentation about the subject?
I want to control arp processing, but not using ip arp inspection command which worked with switched port, not routed port.I'd like to know all cisco routers work with arp throttle. I've tested it on cat4500, but arp throttle did not work. Is there a...
Hi I have a router (Rtr-A) connected to an ATM link. I also have the following connections to Rtr-A:Rtr-B (level-1 router) on S0/0.100Rtr-C (level-1 and 2 router) on S0/0.110The routes I'm summarizing are 196.5.128-131.0/24 into a single route of 196...
in hub and spoke WAN, i got 100 spoke with 56kbps link each, how much bandwidth sould i get for hub link? thanks.
How do I find rommon priv password on 1700, 2600, and 800 series routers?
I would appreciate any help anyone could provide.I have the following setup:1 x 3725 router running IOS 12.3(6c) Release (fc1)1 x NM-1T3/E3 network moduleI just had a new DS3 circuit installed. I'm running a frame-relay network and have the followin...
Hi all, I am a novice and I need some help. I have a 1700 router and I need to know what commands to give the router to point an external ip address to an internal ip address. We already have 3 external ip address pointing to 3 internal ip addresses....
I just received a new 1721/WIC-1SHSDL-V2 Bundle. Unfortunately, the WIC-1SHSDL-V2 is NOT recognised. I already tried updating to the most current IOS release 12.3.12. I tried IP, IP/ADSL & IP/ADSL PLUS Feature Sets.Any suggestions?Cisco Internetwork ...
I have a customer with a triangle of routers connected over 10Mbps Ethernet links. They have a PABX at each site with IP Trunks between them (the PABX's are connected directly to the routers on /30 subnets at 100Mb/Full-Duplex, there is also another...
Hi,we have 85 Frame Relay sites in a hub type configuration. I need to implement frame relay traffic shaping and am aware of all the steps required.The question is, is it OK to configure all the sub int's with the "frame-relay class XYZ" command with...
I am setting up syslog on a 2610 router running 12.0(5) (fc1) IOS. Even though the router will autocomplete the command logging source-interface ethernet 0, it reports that it is an unrecognized command. I am able to set the host and levels, etc. b...
We have a branch location connecting to our corporate office through a leased T1 line. Their connection goes from their Foundry switch to a Cisco 2600 router, which then connects to a 2600 router at the corp office. Last week the IT admin at this o...
Dear All,I find that Catalyst 29xx to 37xx cannot do outbound port ACL. Am I correct? How about Cat4K/6K?Thanksmak
Hi,I need International Quality and Standards Documents for Cisco 2610-xm router and Cisco 2950-24 switch. Also I need introductory (pdf) documents for the two. I searched through Cisco and Google but found no results. Where can I obtain these docume...
Hello, I'm tryng to upgrade a sup 720 to a more recent version of IOs. The current verion of both sups is: s72033-pk9sv-mz.122-17d.SXB1.bin. I'm trying to upgrade to: s72033-jk9s-mz.122-17d.SXB6.bin.I placed the image on a flash card in disk0 and ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |