We try to establish a trunk between a 2950 and a 3548 on int GBIC We forced switchport trnk 802.1Q and switchport mode trunk but the port comes up/down continuouslywhat is the probleme or good configuration
We try to establish a trunk between a 2950 and a 3548 on int GBIC We forced switchport trnk 802.1Q and switchport mode trunk but the port comes up/down continuouslywhat is the probleme or good configuration
Dear all, i have 2 pix 506 e , my network look like this inside network1 ---------->pix1-----crosscable----------pix2 <--------inside network2i can ping pix1 to pix 2 ouside interface but not inside interface . To ping one pix to other pix inside...
When trying to assign an IP address to the fast ethernet 1, I receive the following message : "ip addresses may not be configured on L2 link".What am I doing wrong ?Thank you.
i have setup point-to-point frame relay subimterface in my router i'm using mannual resolution what command can i use with my subinterface to assoicate the dlci to it?A- frame-relay interface-dlciB- frame-relay mapC- frame-relay interface-dlci or fra...
Hiya,I would like to know - is it plausable for me to have a IP device on one side my network and have this channel out over my Cat3500 switch to a router through a firewall too another router which has a ISDN model in it ? Have that ISDN modem dial...
Hello everyoneI tried configuring a catalyst 4506 for NAT operation but the command was not available :)So, I looked for an image supporting NAT on a 4506. None found :)Does anyone know if a 4506 can perform NAT ?How about PPPoE on ethernet interface...
What are the pin outs of the above card when required in a 4-wire circuit?Has anyone used these with EPS8 (UK), and if so, do you have the cable configurations (RJ-11 <-> Tel Jack)?Thanks
Hi, Friends How I know to wich access-group it belongs to each serial interface in the cisco 3600 model?Thanksfabian
In our company we have this router with CPU utilization that moves between the 40% to 99%.I run the show processes CPU and saw that the IP Input process uses most of the CPU time.I am not sure but I am guessing that a huge ACL linked to the Ethernet ...
Hello,we have a Cat6509 SUP2/MSFC2 with NativeIOS 12.1.19E1 with several VLANs. Now we need the restriction that one specific directly connected Server in VLAN 20 can only communicate with its gateway (the MSFC) and not with other devices in its VLA...
I am having a problem viewing any modules on 7500 series routers in CiscoView. All other features appear to be working properly with these devices. The routers are running IOS 12.1 and cisco view 5.5
WE have a problem that has just presented itself this year. Our campus is a 3550 series switches and we have had a couple of instances where students have placed DHCP servers on our network. How are other people handling rouge DHCP serves on their ne...
Hi I need up a ACL (layer 2) in to many swithcs 1900, somebody know if cisco have a tool that allow do it whitout acces each equip?ThanksFabian
We are experiencing problems with crc errors.We have notebooks which need to download system image from our image servers. The clients are connected to 4506 directly while servers are connected to 3750 which connects to 45 with gbic.Recently we notic...
Hello,I have engineers in another country installing a 4 port E1 card in an AS5300. They have installed several cards now and each one shows controller T1 in the running config. I have seen various AS5300s which display controller E1 in the configs...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM | ||
11-14-2024 09:33 AM | ||
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM |