The router 2MB on-board memory and a 4MB PCMCIA flash card. Does anyone know what IOS version supports the "ip nat pool" command?Thanks in advance.
The router 2MB on-board memory and a 4MB PCMCIA flash card. Does anyone know what IOS version supports the "ip nat pool" command?Thanks in advance.
HiIs there any command that will show the routing of specific traffic out a designated interface (HTTP out adsl interface - All other traffic is sent out Serial line? I have attached my config file to explain what I am trying to achieve :-!!!!!!!inte...
We are US based company providing complete end to end prepaid and banking solutions. Currently we are doing dial-up based communication between POS terminals and the authorization server using modem pools. Now we are switching from this method and w...
Hello,Could someone please tell me the command on a Cat5509 to see what MAC address is connected to a specific port?I thought it was sh cam dynamic mod/port - but this shows no entries!Many thanks,Danny,
Hi,I have a problem with cisco catalyst 3750, Version 12.1(19)EA1c. I have to setup shaping on this switchbut i can`t find the right command. I tried do it with policy-map ... and then "service-policy output <policy map name>" but => Assigning a poli...
we have the following problem.We should provide a solution for a , quite , complex configuration a customer wants to achieve.The customer has two sites .on each site there are :- Satellite connection to internet.- CDN ( with ISDN Backup ) connection ...
Hi everyone, I am looking at placing Portfast and BPDU guard on all access ports in a clients network due to them complaining about machines failing to get DHCP addresses at bootup. Trouble is, we do not have control over what is connected to the swi...
On Cisco 6509 sup2, Version 12.1(13)E9, I want to configure command about storm-control broadcast and unicast level, but both two levels must be the same, why?
Have a problem with DFM 1.2 IDU 8. When I launch DFM Monitoring or Admin Console, both work O.K. However, when I exit either of them, The console I'm exiting goes completely grey and console window and IE session becomes unresponsive. I have to end t...
Is it possible to configure the mail notifier to send an email to different email addresses based on different events occuring?For example, if I have a power supply failure event, notify emailaddress1. If I have an event occur for an authentication ...
Is anyone aware of any documents on CCO of how to transition an enterprise network from regular legacy Spanning Tree Protocol to Rapid Spanning Tree Protocol? I found this document that describes RSTP, but it doesn't give any conversion advice:http:...
Setting a rspan for one of our customer. After reading through the document, what confused me is the reflector port. What's the purpose to have a reflector port? Is this for a local monitor device? The way I am looking at the mechinism of the rspan, ...
I'm looking for suggestions on my config for a 3700 router utilizing atm. For an upcoming disaster recovery test, we want to be able to swing the circuit from AT&T directly to the DR Hot Site for the Network test portion. Any advice on the best way t...
i have a NT1 PLUS B , it has U interface ,two line interface and a So/t interface. i connect the So/t interface to the 2600's isdn bri s/t interface ,but it didn't work.the isdn port on 2600 cann't get active at all.when i connect the 2600's ISDN por...
hai all, In cat 3550 everybody knows vlan 1 is management vlan . is there any way can we configure other than vlan 1 as a management vlan ?if your answer is yes , pls let me know how to configure .Thanx®ards,Rajesh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |