when fast switching is enabled pks are load baanced per destination. I am wondering about the need for the maximum paths command then. Thanks.
when fast switching is enabled pks are load baanced per destination. I am wondering about the need for the maximum paths command then. Thanks.
Dear Sir/Madam,How can I configure the 2950 switch to only allow the registered MAC address for connection. Is there any command that can restrict all unregistered MAC address to access the switch by default? Please advise.What is the best solution...
I just wonder if it is possible to erase the configuration on one FastEthernet port or any interface in one command. It is really bothersome to type "no" in front of all the config lines for the actual port, to get it back to dynamic desirable.I have...
I know this thread my sound similar to others, but I haven't done anything like this before.I have 3 point-to-point T1's going from my HQ to a branch office. I have 2 - 2620's with 3 WICS in them. What is the best way to aggregate the three T1's in...
We plan to install two servers (active and standby). The two servers will be using the same MAC due to some reason. When they are conencted to the same vlan, will this cause problem? I worry the switch may claim the mac-address flapping, and disable ...
Hey I need to Document my network which includes around 10-13 cisco switches and routers. Now I dont know where to start. Should I manually document everything or use some kind of a software that automates the documentation process.Please reply back ...
Hi,I wanna configure my remote site to obtain DHCP addresses from my Main site, through a WAN Link that contains a 3662 and 805.But not the same subnet, I mean: my local network has for example 10.11.12.0/24 and the remote network should have 10.11.1...
The maximum supported number of configured DLCIs in Cisco7507Cisco7507, RSP4, Version 12.1(9), DS-3(HSSI)
Hi,Unable to understand this issue. CPU utilization shoots during specific period. The Show Proc Cpu doesn't indicate any process thats eating up cpu cycles. Have a look.
Dear Sir/Madam,How can I configure the 2950 switch to allow only one specific host to acces this switch via particular port?I used the mac-address-table static 0003.ff19.711d vlan 1 interface FastEthernet0/7The PC with this mac address can only use t...
We need to tie in a new building with about 5 connections to an existing network using a switch (SW5).A cost effective way to do this would be to connect to the furthest switch via fiber. However, this would create 4 switches "daisy chained" together...
Hi,I wanted to create a custom report showing certain modules/card type. I tried to create one under RME>Administration>Inventory>Custom Reports and choose report type (card type). Under card type I was looking for wsx6348rj45v but it's not listed. T...
Somebody can find out the cw2000 it supports SNMPV3
I am running Ngenius 1.4 and recieve the above error message? Also, is Ngenius deliver any monitoring ability if you do not have a NAM installed?Tahnks in advance
I have a public firewall at site 1 with a private subnet behind it.I have a public router at site 2 with a public firewall with a private subnet behind it.I have a site-to-site vpn between the site 1 firewall and the site 2 router. I currently access...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |