Has anyone setup the dfm mail notifier,I read the manual and I cant get it to work.the process is running but I am not recieving an emails. thanks in advance for any replys
Is there any technical limit on how many vlans you can put on 1 hsrp group number ? We have like 65 vlans on one box 6500 msfc2 and want to put them all into hsrp group 1 , any reason why we can't do this ?
Hello:Not very familiar with VLANS. I have an HP switch cross connected to our main office and a sperate floor. At times, the port on this switch is near saturation, 90% utilization. Is there anything I can do as far as linking 2 ports (similiar to m...
I have 8540MSR and 8510MSR, and 8-port E1 IMA cards inside. But I have DSLAMs without IMA support, so i should use ATM links. But this cards can't use more than 4 separate ATM links, it automaticly set other ports to shutdown. But i need in all this ...
Hi,Is it possible to configure an etherchannel across 2 switches using stackwise?Does the 3750 suppport .1q in .1q tunneling?Is it possible to create a port channel through .1q tunneling? Imagine that you have 2 switches connected through a provider ...
Okay, it worked for months, now it does not. We have two cat 6500s at the core being core/distro switches. The redundant cat lost its way on boot up one day so we had to massage the boot statements, but did not change the hybrid CatOS or the IOS for ...
Is there a way to control the signal on a serial interface simular to DDR?I'm working on a network that requires only one user on the network at a time (Half-Duplex). The problem is that when the router comes up, it starts sending packets, this signa...
Hello All,I am currently pursuing my CCNA. I have taken the Intro to Cisco Networking and the 5 day ICND classes. I am preparing to take the exam in couple of weeks and I wanted to practice the commands I learned in class for the simulation portion...
Hello, I just received a new cisco 3550 - 24 port switch with cisco IOS 12.1(19) installed on it. The problem that I'm having is that off boot the switch is giving me the following problem:-------------------------------------------------POST: C...
We added VTP domain name to C6000, before addition VTP domain name was empty and switch was configured to VTP server mode. Another switch C5500 was attached to C6000 with trunk link. It was in different VTP domain and it was in VTP client mode. C6000...
How can I find out what Module\Port a device is attached on a Cat Switch? If I know the IP Adress and/or MAC Adress is there a command or commands that I can use to trace to the MOD\Port?Thanks,Mike
Hi, this question is looking like the one from Tan, submitted Jul 2, 2002, 11:17am PST. I have some new question and comments concerning this problem:I have configure two routers on a network with HSRP.I did a FTP from a client behind the 2 routers t...
I have what I hope to be a relatively simple problem.I have router1 which connects to 10.15.64.0/21, 10.15.80.0/24, 10.15.81.0/24, and 10.15.83.0/24.Router2 connects to 10.15.80.0/24 and 10.15.62.0/24 and is the gateway to everything else.Router2 is ...
In Cat3550, the ospf load balance with equal cost (2 routes) fail when change adjacency neighbor.When neighbor is up the load balance don't work.the workaround is:clear ip route * orclear ip ospf 100 process
Has anyone come across the following behaviour. Upgrade the IOS on a 3661 router to an IP plus version to handle E3 Network module. The current flash files were copied to a PCMCIA card. After deleting all files in flash when we try to copy the new im...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
.jpg "VIP Community Legend"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
