Are there any log files to view that track user activity in Cisco Works? When using the Tacacs+ module for athentication it only shows logins.
Are there any log files to view that track user activity in Cisco Works? When using the Tacacs+ module for athentication it only shows logins.
Hello,How can I format a bootflash on MSFC2 if there is no file on it and MSFC2 is in rommon mode? (Set by confreg).'dir bootflash' show some errors, so I want to reformate the bootflash.Thanks Ruedi
HI ThereI have a minor problem with the startup/running out of sync report. When i make a change on a box with netconfig eg. delete a entry, the running config on the cw2k is updatet due to a syslog message but the startup config is not updatet even ...
Hi,we have a Router A in a subarea. The router A has two connection to area 0 via different ABRs ( B and C). Both ABR are ASBR at the same time. In addition we have a third ASBR (D) in the area 0. ASBR C and D advertise the same external route (type ...
Hello, i have 1720 router, i would like to get ip address for my F0 from DHCP.Can u help me??Best regardsKheireddine
Hi,I have two Switches IOS Cisco 2924 one with IOS (C2900XL-H-M), Version 11.2(8)SA4 and other with IOS (C2900XL-H-M), Version 11.2(8)SA5, when I try to configure trunk, the command switchport mode doesn't have the subcommand trunk, just have the sub...
Hi All, What parameters should be tuned on XOTover VSAT with delay around 600ms?to get best performance??anybody has experiences on it or have good docs?thanks, ali
Hello,I have a Cat 6509 with a SUP 1.It is constantly resetting itself with the following error during boot up. Any ideas on this one?Thanks, MarkSystem Power On Diagnostics CompleteCurrently running ROMMON from S (Gold) regionBoot image: bootflash:c...
Dear Sir,We have a setup with router connected to internet on public IPRouters ethernet port is also on public IP connected to PIX outside interface.PIX outside interface is also on Public IP.Problem is sine the setup is live we cannot afford downti...
Dear Sir,We have a hub and spoke WAN with all the major locations connected over leased line with isdn backupOne of our remote location has only ISDN dialup as primary connectivity.At central location we have a citrix server which is being accessed b...
I used "show test" command to check the temperature of 4006 switch,the result is as follows,and no error occur:4006> sh testEnvironmental Status (. = Pass, F = Fail, U = Unknown, N = Not Present) PS1: . PS2: . PS3: . PS1 Fan: . PS2 Fan: . ...
Hi, i need to configure 12 vlans but i need to make that some of them can see in one way, for example vlan 12 can reach vlan 9 but vlan 9 should not reach vlan 12, what is the easiest way to do this?are the access-list the only way to do it?thanks
Greetings Cisco Experts,I can see a Virtual-Access1 interface when I do the sh ip inter brie,can someone tell me that what is the function of this interface?Thanks in advanceaht
i am just wondering if 805 router with 12.2 basic IP software supports BGP protocol..what i knew from a techie, basic IP image will support BGP.. please advise me.regardstaib
Hi Guys !I have a Cisco 3725 Router with 2 ethernet interfaces and 4 BRI S/T interfaces. Ethernet0/0 is connected to Internet and Ethernet0/1 is connected to my LAN. I want to configure DDR so that whenever internet link via Ethernet0/0 is down route...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |