Other Network Architecture Subjects

We recently converted 2 6506-E chassis to use VSS w/ Quad-Sup and noticed that several SNMP OIDs we used for monitoring have stopped working. OID 1.3.6.1.4.1.9.9.217.1.3 only provides module statistics for the active chassis, rather than both. OID 1....

Friends,I would like to request your insight on the following. Scenario:Two 1921 routers interconnecting 2 sites (site A and site B) via 10 Mbps line.I would like to implement QoS on the link so that some specific groups of servers on site A communic...

Hi,  When I enter any commands on my N5k's, I see echos of the full command, date/time stamp, and OS version: # sho run!Command: show running-config!Time: Wed Nov 26 15:42:04 2014version 6.0(2)N2(2)<then running config is shown> Why is this?  It does...

After greeting... PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.Current configuration on bus mb1 has a total of 0 bandwidth points. This configuration is within the PCI bus capacity and is supported. PCI bus mb2 (Slots 2, 4 an...

Can anyone tell me if the Cisco stock for smartnet device replacement / RMAs for devices in Brazil (specifically Sao Paulo) is stored within Brazil? Ie if a device in Brazil covered by smartnet needs to be replaced, does the replacement come from wit...

Hi, I am having an issue getting a site to site vpn setup to work. Here what the logs are showing me4|Nov 21 2014|08:22:03|113019|||||Group = 0.0.0.0, Username = 0.0.0.0, IP = 0.0.0.0, Session disconnected. Session Type: LAN-to-LAN, Duration: 0h:00m:...

Hi Cisco Community! What is the resume term for putting in new Cisco hardware (routers, switches) and copying the configuration from the old Cisco hardward to the new hardware? Thanks!

Hi there,I'm looking for some guidance when setting up failover on our network.  I've attached a diagram which hopefully explains how my network is set up for internet access.Basically I have 2x ASA configured in an Active/Standby pair, each is conne...

A while back I found a tool in Cisco's web site that would allow you to select a switch, enter in its modules and check the configuration for errors... Does any one have a link to that tool? I cannot for the life of me find it again...

Our modem can only be put in a room where someone sleeps.The lights on our Cisco phone/internet modem are too bright.  The lights are seeping out the vents.  There is no other solution but to put the modem in a smaller cabinet.The cabinet is made out...

I installed NIC Drivers to a Standalone server, installed Teaming Protocol, Used enictool.exe to configure VIC Team (-m 4 (LACP)), but I need to understand what "connection" Load balancing method means. By default Connection is used, but there are op...

Hi Team, We are Using a asr903rsp1-universalk9_npe.03.11.01.S.154-1.S1-std Ios For cisco ASR 903, I want one Suggestion if I want to Upload/Copythe IOS from active to Standby Than what is the Procedure and the Standy controller is on rommon mode how ...

Hi Team, We are Using a asr903rsp1-universalk9_npe.03.11.01.S.154-1.S1-std Ios For cisco ASR 903, I want one Suggestion if I want to Upload/Copythe IOS from active to Standby Than what is the Procedure and the Standy controller is on rommon mode how ...

Hi therei have a serious problem in my network that i need an urgent solution fori have got an 2811 router and a 3560 Cisco catalyst switch the 2811 router has two interfaces (f0/0 & f0/1) f0/1 is connected to the Wan and f0/0 is connected to the 356...

Hi everyone,I have a Cisco 2911 (IOS ver 15.3(3)M) in our branch office and Cisco 7204VXR (IOS version 12.4(4)) in our headquarters. They should be connected to each other via IPsec Tunnel over EIGRP.On the Cisco 2911, I receive this from the log:Nov...