My question is the following:Can I install nGenius RTM on the same server that is running CW2000?Would it work? Are any special requirements to do this?Any recommendations?Thanks.
My question is the following:Can I install nGenius RTM on the same server that is running CW2000?Would it work? Are any special requirements to do this?Any recommendations?Thanks.
i have a 7507 with a vip240. recently we had to change that card becuase a crash. after made change i found with the cpu in vip card has a high % of utilization; the question is : Is normal that situation. the utilization is 95% average.
Hello,I see that in most campus networks layer 3 switches are used in core and distribution layer and layer 2 switches in the acces layer. If not considering costs, are there any benefits of implementing layer 3 switches in the access level? I've re...
I have a pair of Cat4006 switches in the datacenter that I just installed with the 48-port 10/100/1000 BASE-T blades. These things are beautiful! A problem I'm having, though, is that I can't seem to set the ports into full-duplex gigabit mode. I ca...
What is the best way to determine that both B-channels are being utilized on a BRI. Thanks devans
Hi,A device that has been discovered from ANI must be deleted from the db to be rediscovered. How could I perform that ? from the GUI ? from the commande line ?Thanks.Patrick Vignaud.
I have a frame circuit that has a CIR of 256 and an access-rate of 512. The telco has physically provisioned this at the remote site to use all 24 channels and they choke it down to 256/512 in their equipment. My frame-cloud is a T1 at my host site...
We are having some problems trying to backup configs from devices located behind firewalls. Ciscoworks is able to gather information from the device (i.e. get, get reply). We are source NATing the Ciscoworks server, the configuration backup is genera...
What happens if you're doing SPAN with a source Gigaethernet port and a destination 10/100 port? Will the buffers fill and packets started to be droped?What if you're monitoring a trunk port? Do packets arrive ISL or DOT1Q encapsulated although your ...
Hi.......a quick question for da pros out there:Using a 3640 router, I was wondering if there is any way possible to assign 2 different IP addresses to a single ethernet interface.Thanks.....J
Hi Cisco Fan´sDoes anyone know if the cat 4500 (SUP IV & WS-X4306-GB) supports the GigaStack or 1000BaseT gbic?Respectively if its on the roadmap ...Thanks for answersJens
All,I have a legacy network domain running BSRv2 (pim-sparse) and I want all of the new network (which has no mcast enabled) to run Auto-RP (pim-sparse-dense with sink RPs). In the new network domain, will leaf routers accept auto-rp and bsr group-t...
hii have 2620 router, and i would like to create subinterfaces on my fastethernet 0/0when i create it, i would make an ip address but this is the message errore:Configuring IP routing on a LAN subinterface is only allowed if thatsubinterface is alrea...
I am having a problem with configuring an atm point-to-point interface with a priority-group. I'm able to enter the command w/o any errors, but when I go back to look at the config, it doesn't appear to be configured.I also have a seperate group of ...
Greetings,I am getting following errors on my 3640 routers. I don't know what it means?GMT: %AMDP2-FE-6-EXESSCOLL:Ethernet0/0 TDR0 TRC=0I am getting some input and output errors on e0/0 interface.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |