out of curiosity is there a way to compress specific traffic on your router via ACL or some other way? also how good is the compresssion?-mike
out of curiosity is there a way to compress specific traffic on your router via ACL or some other way? also how good is the compresssion?-mike
I have a 4006 with the L3 module and many VLANs. Each VLAN has a subinterface created on the L3 module for routing needs. Can I configure rate limiting for these sub interfaces or just the main interface?Also, if I am not able to limit the sub inte...
I have four buildings which are 2 Km apart and one more buildings which is 500Km apart.I need to connect all these.What are the ways i can connect.I need your suggestions .ThanksRgsCavin
There are 4 serial links on Cisco 3662,the configuration is just so simpleand there are some access-list.When I stop using Cisco 3662 and move all 4 serial links to Cisco 7206,and then interfaces are up,and apply all access-list, and then test ping,c...
Is there any appliactions that will not work with NAT & PAT.Basically, we access PeopleSoft 2 tier, 3 tier, web, Mainframe access, 3270 access. and I need to configure PATing and wanted to know if they will all work using PAT.
Do the Ethernet interfaces on the new 2600XM routers support 100Mb-Full Duplex settings? I think the old platform did not support this, but I wanted to confirm.ThanksJericho
My question is the following:Can I install nGenius RTM on the same server that is running CW2000?Would it work? Are any special requirements to do this?Any recommendations?Thanks.
i have a 7507 with a vip240. recently we had to change that card becuase a crash. after made change i found with the cpu in vip card has a high % of utilization; the question is : Is normal that situation. the utilization is 95% average.
Hello,I see that in most campus networks layer 3 switches are used in core and distribution layer and layer 2 switches in the acces layer. If not considering costs, are there any benefits of implementing layer 3 switches in the access level? I've re...
I have a pair of Cat4006 switches in the datacenter that I just installed with the 48-port 10/100/1000 BASE-T blades. These things are beautiful! A problem I'm having, though, is that I can't seem to set the ports into full-duplex gigabit mode. I ca...
What is the best way to determine that both B-channels are being utilized on a BRI. Thanks devans
Hi,A device that has been discovered from ANI must be deleted from the db to be rediscovered. How could I perform that ? from the GUI ? from the commande line ?Thanks.Patrick Vignaud.
I have a frame circuit that has a CIR of 256 and an access-rate of 512. The telco has physically provisioned this at the remote site to use all 24 channels and they choke it down to 256/512 in their equipment. My frame-cloud is a T1 at my host site...
We are having some problems trying to backup configs from devices located behind firewalls. Ciscoworks is able to gather information from the device (i.e. get, get reply). We are source NATing the Ciscoworks server, the configuration backup is genera...
What happens if you're doing SPAN with a source Gigaethernet port and a destination 10/100 port? Will the buffers fill and packets started to be droped?What if you're monitoring a trunk port? Do packets arrive ISL or DOT1Q encapsulated although your ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |