I have a catalyst 4006 with processor III, level 3, and in the show interfaces output the “input queue” in very very high, in several of they, but no droop paquets.For exampleFastEthernet2/47 is up, line protocol is up Hardware is Fast Ethernet ...
-
Announcements
(5) -
Automation
(1) -
Branch Router
(5) -
Buying Recommendation
(79) -
Catalyst 2000
(1) -
Catalyst 3000
(3) -
Catalyst 4000
(1) -
Catalyst 6000
(1) -
Catalyst 9000 Switches
(2) -
Catalyst Switch
(1) -
Cisco Cafe
(25) -
Cisco Digital Network Architecture-DNA
(1) -
Cisco DNA Automation
(2) -
Cisco Software
(2) -
Cisco.com Idea Center
(2) -
CiscoChat
(1) -
Collaboration Solutions
(2) -
Community Awards and Recognition
(1) -
Community Feedback Forum
(18) -
Community Ideas
(10) -
Commutation
(1) -
Configuration
(4) -
CSC Content with No Valid Community to Post
(2) -
Data Center
(1) -
Discusiones General
(1) -
DMP
(1) -
EEM Scripting
(1) -
General
(6) -
Guest
(1) -
Integrations
(2) -
Intent Based Networking
(1) -
IP Phones and Accessories
(2) -
IPv6 Configuration
(17) -
LAN
(2) -
LAN Switching
(12) -
LAN Swtiching
(2) -
Network Management
(9) -
Optical Networking
(2) -
Other Cisco.com Ideas
(1) -
Other Collaboration Topics
(4) -
Other IPv6
(1) -
Other Network
(822) -
Other Network Architecture
(6) -
Other Network Infrastructure Subjects
(1) -
Other Networking
(55,046) -
Other Networking Topics
(1) -
Other Routers
(5) -
Other Routing
(5) -
Other Routing and Switching topics
(1) -
Other Service Provider Subjects
(1) -
Other Switches
(6) -
Other Switching
(6) -
Otros temas de Routing y Switching
(3) -
Packaged CCE
(1) -
Positive Feedback
(53) -
Routage
(1) -
Routers
(6) -
Routing
(15) -
Routing Protocols
(7) -
SD-WAN
(6) -
Switches
(2) -
Switching
(6) -
Swtiches
(4) -
WAN
(1) -
Wi-Fi 6
(1) -
Wired
(1) -
Wireless
(1) -
Área de Ayuda en español (help)
(1)
- « Previous « Previous
- Next » Next »
Forum Posts
Hi, I have a scenerio whereby the HQ needs to have a (or few) RAS server that to cater for the remote dial in from more than 100 remote sites.The remote clients some are using ISDN and some are using analog lines.Please suggest the Cisco Products tha...
Resolved! AUI-Transceiver supports full-duplex ??
Hi,I have a Cisco7505 with a Dual-Ethernet-Module which has only AUI-connectors. I enteres full-duplex (which was possible) and tried an AUI-converter but I got duplex-problems.Now I am not sure if my converter supports full-duplex or if there is a...
Im trying to disable certain traps in the DFM, VHM, One such trap would be DMH Server Down. Im setting up mailing and I really dont want to me mailed on this trap. When I unsubscribe from this trap in the EventProfile, I still get mailed on it. I...
Hi I uegently need a catalyst 2900xl iosRegardsfarshid
Below are the configuration for an ISDN router to enable PC dialin remotely, but the authentication isn't successful. From the debug mode, I can't see any username or password being exchanged. Please help !!Building configuration...Current configurat...
hi! when i working with 3550-emi switch , i find some problems . 1 in my network ip address 10.12.82.0/24 were subneted into 8 vlan the 3550 act as layer 3 switch , when i config the switch ex vlan, ip routing correctly,but the...
Hi, I've two areas area 100 & area 200. area 100 -> ABR for area 100 -> ABR for area 200<-area 200I just want ABRs to advertise "default-information always" to thier respective areas. But when I say "default information originate always" in the ABR...
I have two buldings with 1000 meter. I have betwenn these bulding a twisted cooper cable (224 pairs) wich is use to deport a phones line from one bulding to another.To day i use two modem from RAD Communications but the speed is limited at 2 Mb. I wa...
We are trying to run ip accounting on a router to show how much traffic is going to particular ip addresses. What happens when the buffer reaches the maximum size - does the information get overwritten or does the router simply stop logging?Is there ...
Hi,I'm using 3550 12.1(12c)EA1 as access routeur. When I add an Input ACL I have an FM-3-Unloaded message. I'm using the SDM access template.How can I select which ACL will be installed in Tcam ?How can I see which tcam is used 1 or 2 ?Alain Tremblay
Hi, I have a scenerio whereby the HQ needs to have a (or few) RAS server that to cater for the remote dial in from more than 100 remote sites.The remote clients some are using ISDN and some are using analog lines.Please suggest the Cisco Products tha...
I am connecting a 2950 to a 6509 in the following way. The Cat 6509 has MSFC which does the routing. My intention is for the Cat2950 to receive info from the Cat6509 MSFC.A cross over cable between Cat 2950 int fa0/1 to Cat6509 7/4. I have configured...
Hi,If you are connected with a telnet session and what to see the debugging messages, which command is required to make this happen?Thanks,Peter
Hi AllWhen I push the "Stat" button one of my 3550-48's (to see the bandwidth utilization), all the LEDs on the front panel lights up. Now this 3550 has 23 2950-24's connected to it via 100MB trunks, as well as a 2980 via a Gig trunk, and another 355...