its possible to balance several wan links. 2 situation, one if de link belong to the same ISP, 2 if the links belong to several ISP.My question is, can we do that?
its possible to balance several wan links. 2 situation, one if de link belong to the same ISP, 2 if the links belong to several ISP.My question is, can we do that?
I am currently testing a different brand router that does not support Cisco's Frame Relay Encapsulation. However it will be communicating to a T1 Frame Interface on a Cisco 7507. Here's where my questions comes in: If I change the encapsulation ty...
We are trying to configure fall backup for a 2611 router. Our main RF link WAN broadband radio with ethernet feed to router is connected with e0/0 )& e0/1 is connected with local network.WE have an additional BRI CARD which has to be configured as ba...
In reality I'm looking for a CW2K developers guide that defines the interfaces in the CW2K environment. I'm working to tightly integrate CW2K into an end-to-end management environment, instead of having provisioning and operations having to open mul...
Hi,On the RSM module, how do I clear the statistics on the buffer and On the ATM module, how do I clear the statistics on the buffer and controller?TIA.PF
I have this issue:R2: running area 0 and 3 (ABR)R1: running area 3 only (Internal router) and also is ASBRI created a loopback interface on R1 assign ip address 150.50.200.1 and thenadvertise this network in RIP. I then redistributed RIP into OSPF,...
I have a Cisco 1720 router with leased line to internet and ISDN backup to internet. The ISDN backup is using "Backup interface" method. My ISP assign different IP pool for my leased line and ISDN. So I use route-map so that the router will select ap...
Hi All,In 3550 manual, cisco said that you should use "flowcontrol send off"and "flowcontrol receive off " first before you use "mls qos"command. But I had seen serval sample and none of them use the "flowcontrol"command. Can any body have idea that?...
I have a cat 4006 connected to a PIX 525 on the DMZ interface. the PIX is running IOS vers 6.1. The 4000 is running cat os 5.5.(10) at layer 2 and IOS version 12.0(14)W5(20) on the router card (WS-X4232-L3). For the past three days I've been noticin...
Hi, I have read in documentation and in conversations, that if I aply an ACL in a sub-interface PORT-CHANNEL it won't work, but I have tested and worked.Instead the IOS report that don't support the command, its works. Down what happened .Can anybody...
We have a MAN with 7 routers connected to a shared 100MB fiber ring. We need to run cdp to see the connections between these devices. The problem is our service provider has a Cisco network management device that can only run at 10 MB/half duplex. ...
Hello,On the url: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-cd-one I could find the patch cwvms-common-services-1.0-p1-win.zip. How I know I need the common services with VMS. But what is the reason to put this patch with the cd one patches? ...
how do I can, to verify the mmtl (Modem Management License) is installed in my router ?Sorry for my english.thank
I have 1 site dialling into another site on backup and I cannot get the ppp part working. Debug output shows the following:-Apr 1 13:52:19.533 GMT: BR2/0:1 LCP: State is OpenApr 1 13:52:19.537 GMT: BR2/0:1 PPP: Phase is AUTHENTICATING, by bothApr ...
Can anyone tell me (or point out a cisco url) that mentions which process belongs to which module ? My reason being, I have CM installed along with RME,DFM etc and I want to stop CM but not to uninstall. So I want to just stop all the processes asso...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |