Other Network Architecture Subjects

HiI have a problem like this can any one pls advise.My network is connected to remote branch office through cisco 3600 router using mico wave link.There is no firewall between these two networks.The problem is i can able to ping the remote server but...

Can one port be member of two or multiple vlan's. ?? Of course at a time only one VLAN will be active.

Each of the three routers had the same exact config. except for details such as username/password for CHAP, IP's, phone #'s, etc... The config'd items were the same.1 BRI int2 Dialer Ints (dialer profile for each of the other 2 sites)1 dialer poolTh...

Hello All: one customer asked me the maxism vlan intances C4006 SupIII can support. He give me a formula: vlan numbers on the switch *trunk port numbers on the switch +non-trunk port number on the switch=vlan instances. He said through the for...

My customer is building the network which consisted of Cisco7200 with NPE-G1. Since the "NAT Integration with MPLS VPNs" function is needed in the network, it is required for there to be support by IOS 12.2T. However, NPE-G1 does not operate in 12.2T...

hi, i'm a network engineer in japan.i need a help from you. i wanna configure no service pad command in CatOS.i can't find any set command in WS-C4003 Software, Version NmpSW: 6.3(2a).and what's PAD(packet Assembler/Disassembler)??also, i can't set ...

I am having some trouble connecting the two with isdn you will find floating interface routes for the isdn. when running debug I get on the WHSE-TO-MAIN Router "cause I =no route to network", and on MAIN-TO-WHSE i get "cause i = host rejected"any th...

Hi people, how can I to change the name of binnary file allocated in flash?For example, when I gave a show version command in router prompt, it appears a name of system image flash:System returned to ROM by reloadSystem image file is "flash:c3640-jk...

I'm very confused now by all the terms which are used concerning bandwitdh managment.I got 2 questions on which I can't find an answer or I get lost by all the technical terms.1. Is it possible to limit users (by MAC/IP) bandwidth?2. If so, which pr...

we are going to purchase cisco 3550 switches for our DMZs setup, we would like to utilise the Private VLAN (PVLAN) features in order to protect our individual server from any attack or any compromise servers. Can any body highlight some more on this ...

I am doing a migration of all our ADSL routers (non-cisco) to 827 Cisco router. Until now I had no problem at all. But with one I have a routing problem :This is my config :Cisco827#sh runBuilding configuration...Current configuration : 1199 bytes!ve...

Here is a crude picture of the topology:192.168.0.x<--->192.168.0.1/e1-c1605-e0/1.1.1.1<--->1.1.1.x**e0 address space has been changed to protect the innocent since it is public address space The PCs in the 192.168.0.x subnet were originally slated t...

I am configuring a PIX 515e Software Version 6.1(4) and would like to give access to all traffic accessing the DMZ. I thought this would work: ("dmz" is the interface name)conf taccess-list acl_dmz permit ip any anyaccess-group acl_dmz in interface...

Dear All, I noticed a peculiar event happening to a 4507R with Active SUP IV in slot 1 and Standby SUP in slot 2. The active and standby where in RPR mode.I used logging console and checked that all change where synched with the standby s...

Several computers on our network attempt to become the master browser. We have done the following and it STILL does not fix the master browser issue.Our vlans are configred as follows: ip access-group 100 out ip helper-address 172.19.1.1 ip helper-ad...