This morning one of our 2950 drop offline. When I access it through the console the following error kept showing up SCHAN ERROR INTR: unit=1 SRC=6 DST=5 OPCODE=20 ERRCODE=5. I reloaded the switch and it is working well but I was just curious if...
This morning one of our 2950 drop offline. When I access it through the console the following error kept showing up SCHAN ERROR INTR: unit=1 SRC=6 DST=5 OPCODE=20 ERRCODE=5. I reloaded the switch and it is working well but I was just curious if...
I have a router with the address 192.168.0.103 on the E1 interface. I need all traffic sent to 192.168.0.103 (or all traffic received on E1) to be sent out the E0 interface. The destination address needs to be changed to 192.168.0.33. If it can no...
Please can you confirm the version of code required for the Module to be accepted by a cisco 2610XM. Or any information which may solve this problem.i am running IOS c2600-is-mz.122-12a.bin (IP PLUS)cisco 2610XM (MPC860P) processor (revision 0x100) w...
In which three situations is a hold-down timer reset? (Choose 3) A. When the hold-down timer expires. B. When infinity is finally defined as some maximum number. C. When the router exchanges update summaries at area borders. D. When the router detect...
Please kindly help me if anyone know how to config a cisco3550 router such that routing between 2 vlan is possibleThe Problem Detail:Setup=====FA0/1<->PC A (ip=192.168.70.1, gateway=192.168.70.254)FA0/2<->PC B (ip=192.168.80.1, gateway=192.168.80.254...
correct me if i'm wrong but the acl applied with this command"ip nat inside source list 1 interface Ethernet0/0 overload"should tell the router which interesting traffic to nat. packets that match the acl will be translated, those that do not will ju...
Hello everyone,i am having a problem connecting to a networked resources located in a different network. I tried different methods of troubleshooting but i can only telnet to the other net. i cannot access any software directly. what else can i do to...
Hello All,I have a customer who is utilizing both EIGRP and OSPF routing protocols in their network. Their network falls under the AS of my company and we would like to move tem to a pure OSPF routing environment, with their own area id. Their net...
Is it possible to load balance 2 - 1Mbs SDSLs in a single router? Envision an low end DSL router with NAT & DHCP on the internal LAN with the router balancing packets between two SDSL circuits to a local ISP.Which router would be recommended? Are t...
I have a switch connected to a RPS300. When I fail the AC input to the switch, the RPS supplies power to the switch. However, when I restore the AC power, the RPS remains blinking Green and when I press the standby/active button, the switch reloads.I...
see the sketch map: (4006)---(3550_1) |____(3550_2) |____(3550_3)VLAN 1: 3550_1(192.168.1.0)VLAN 2: 3550_2(192.168.2.0)VLAN 3: 3550_3(192.168.3.0)I want to set 4006 as a DHCP server and assign IP to 3 switchs, how should I configrue my swit...
Anyone knows how could sniffer docsis frames? I have an analizer that understand them, but where can i put the sniffer to collect the docsis frames?Thanks,Rafa.
In a complex Switch Network I lick to configure the vlan ports how should normally blocked by spanning tree with a bad priority value. I have the concept the Backbone links should never blocked until the Backbone itself is redundant and has a better ...
I have a 2651 that the T1 controller keeps bouncing. How could I check for slips or errors through the IOSThanks
I want to filter all input packets (IP and non-IP) from a virus PC. Because the user will change his ip address, I have to filter it out by MAC address. This function can be worked in Catalyst 3000 series but I can not find similar feature in Catalys...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |