Other Network Architecture Subjects

I am running some tests leading up to substantial change to our OSPF areas.As you know our area 0.0.0.0 currently ranges from 10.0.0.0 to 10.31.255.255and area 1.0.0.0 from 10.32.0.0 to 10.63.255.255 with the following commandsunder ospf router:-netw...

If I have a Policy route set up that says: Route a.b.c.d to interface serial 1, all the packets match the criteria, however the serial 1 interface goes down. Will the router then kick the packets back to the routing table ? Or will they be droppe...

I am looking for some software that will imitate our LAN and WAN infrastructure. The aim is to use this before I make any changes on the live system. i.e. if I change the VTY revision at 1 site what impact will that have on another etcthanks

Hi gents,I have received a new 2948G-L3 and have uploaded the latest IOS cat2948g-in-mz.120-18.W5.22b.bin.I do not undertsand why I cannot enter the Vlan Database using the "vlan database" in privilege mode !!!!!I hit the following message: "No Virt...

We are looking at trying to integrate CiscoWorks in to our Big Brother Server monitoring set up. I was wondering if anyone else has tried this and knows of any pitfalls, or even if it can be done?

I am having trouble getting a T1 up for a customer. I have a 1720 on my end,below is some output from the router, CPE is "webranger" settings look right, clock source set to internal on the 1720, line on the webranger. Can't seem to get the two to co...

The diagnostic log time is off by as much as 3-5 hours on each of our Catalyst 3500's (viewed through the web browser). I have checked the system time management and the date & time are correct. Is there a command line fix to refresh or reset the dia...

Currently I have a Cat6k running with the following modulesWS-X6k-SUP1A-2GEWS6248-RJ-45WS-X6182-2PA (flexwan)Show version: Cisco Internetwork Operating System SoftwareIOS (tm) c6sup2_rp Software (c6sup2_rp-DS-M), Version 12.1(4)E3, EARLY DEPLOYMENT R...

Looking for guidance on which of the DLSW mib traps and Cisco MIB traps need to be used to manage a DLSW environment proactively and what severity level to set on the management system (HPOV).Also which of the DLSW syslog messages would be relevent t...

I was looking for some advice on OSPF. ( or other if more appropriate ) The scenario is a Windows 2000 AD Server with routing and remote access OSPF turned on. A Cisco 2500 Router with OSPF Setup. The Remote office workstations Default Route is ...

Can anyone confirm if the Cat6K ip forwarder process forwards frames that are broadcast to the specific subnet broadcast address and not the 255.255.255.255 address?i.e if a workstation sends to 141.144.5.127 which in this case would be the broadcas...

I have one Cisco 2621 router with two fast Ethernet interfaces, how I can use both interfaces for load sharing and redundancy. for your information I have only one subnet in my lan 172.16.1.0/24?

I am a beginner in cisco IOS command,, so please excuse the basic question. I am working with a Cisco 2620 w/ith IOS 12.2.I would like to route all packets comming from xxx.xxx.127.138 to yyy.yyy.127.137.Is the configuration below ok? or shoul I defi...

I am looking for some software that will imitate our LAN and WAN infrastructure. The aim is to use this before I make any changes on the live system. i.e. if I change the VTY revision at 1 site what impact will that have on another etc thanks

Hello, in my installation CW2000 LMS 1.1 on NT4 the ChangeAudit process isn'nt running. If i start it manually via server configuration->administration->process management or via pdexec, the process runs only several seconds. The log files are not up...