I have a 4500 router and the CPU Utilization is running at peaks between 75% and 90%. My question is this, can adding more memory help the CPU Utilization or will I need a new router?Thanks Larry
Can someone Help me.I have a switch C3524XL and i would change the config-register.Please can someone tell me how I can do this in Rommon mode. And in the normal working mode.Take care Rommon is a little bit different. I tryed everything but it will ...
I recently upgraded the IOS on a 3640 router, just to find that the FastEthernet interfaces vanished upon reboot. The version was 12.1 -I then tried version 12.09 and ALL my interfaces vanished with the error "undefined port adapter in slot 0"What'...
Hello,as regards the bug CSCdt62732 and the field notice "Cisco CatOS Telnet Buffer Vulnerability"we have to update the supervisor software on our Catalyst 5xxx switches.The running CATOS software has the version 4.5(6). We have installed following t...
Hi,In a ethernet vlan, usually on vlan is mapped to one ip subnet. In token ring vlan enviroment, is there any mapping among TrBRF vlan, TrCRF vlan, and ip subnet?Thanks for you help.Fujin
HiI had problem for Dialin analogin modem.If user connect in my router I saw interface async up but then down suddenly what I can do this castFeb 19 15:37:20.021: As103 PPP: Treating connection as a callinFeb 19 15:37:21.025: %LINK-3-UPDOWN: Interfac...
Has anyone had any experience and success interfacing CISCO WIC-1T modules with the EIA-530A port on a STE (L3 Communications) secure telephone?We have had little luck in getting these interfaces to work together.
We have two cisco2621 routers with BRI interfaces acting as backup for a serial link. Whenever we try and make a call we get the message "no free B channels" despite the fact that the channels are not in use. we have had the line tested by the telc...
We are having problems with ISDN BRI connections. We are in the UK and using basic-net3 switch type. When the line is connected it goes through the correct setup and ends up with layer 2 in Multiple Frame Established state. However after around 30 s...
Hi all,I created an additional vlan the other night (vlan 2) and configured ISL trunking using a 3662 between vlans 1 & 2. The 3662 has wan connections to other remote sites. The switches I am using are 2924's. Once I had configured the "router on a ...
Is there a easy way to have a device (router or catalyst switch) write back to a tftp server other than where Ciscoworks is running from ? We have a setup where Ciscoworks is on one server and our main tftp server is at a different address . Ho...
Hi David, I am doing a project for Network Management class at RIT. I would like to use Cisco products for my projects, since I found Cisco web site very helpful. I would like to get some information on managing a PBXs tied to a Virtual Network. All ...
I am in the process of changing my VLAN management interface from the default of VLAN 1 to VLAN 2 and encountered the following:Current IP address of SC0 interface is an IP network that is not defined on my RSM. The IP network is configured on our 75...
Who will prompt where to find the documentation on this IOS? I found the documentation on native IOS. Has found also the documentation on CatOS with small marks about MSFC IOS: interVLAN routing, Highavailability. But MSFC IOS does not concede on siz...
I have an RFP that outlines the spercs below and i am a bit confused about it.SpecsMinimum 6 analog voice channelsFax 2 channelsLow speed data transfer 4,8 to 19,2 kbps in sync/async protocol (V24/RS232 interface)Medium speed data transfer using ISDN...
