On extended access-list statements, what is considered the source address and what is considered the destination address? For instance, is the source coming from the WAN interface or the Ethernet interface?
On extended access-list statements, what is considered the source address and what is considered the destination address? For instance, is the source coming from the WAN interface or the Ethernet interface?
I need some advice with VTP domains:I have two remotes sites with Cisco Catalyst 3524XL switches. SiteA has 3 switches and SiteB has 2 switches. Each Site is it's own VTP domain, and seperate subnet. Someone will move 1 switch (VTP Client) from Si...
Hi,I am using an AS5300 for authentication for a small ISP. I have two T1's for connection and 48 modems. When I try to do a multilink ppp connection with ISDN my authentication fails, but if I change it to use only a single line the authentication w...
In a two-router network, separated by a T1 point to point on S0 of each router, there are a few IP devices/hosts off each E0 at each end but more importantly, a mission-critical async serial device on an async port at each router. We must ensure the ...
is there any way to make a static nat on cisco 805 router with a dialup connection to allow inbound connections to a server in my lan?
I have a question about Real Time Monitor and the NAM module that I have installed in my 2 6509s. I would like to know if it is ok to span the entire backplane of a 6509 to the NAM for closer analysis with Real Time Monitor 1.3? We currently only h...
Platform: 3600,2600,1700 12.1(?)Is there any way to add interface description into console or syslog message for an interface up or down event.
I need to delete some files somewhere because CW2k has filled up 30GB!!! Any help on where to start looking to free up disk space would be much appreciated. I've already hit the .logs btw.Thanks in advance,Jeff
Hello, I want to know how NAT/PAT feature degrade performance in a Catalyst 6509.Thanks a lot.Regards, Anacelia
currently i have 2 units of Cisco 1601R router, both router are reporting the same problem. The problem of the router was the serial ports have no connection. Suspecting the serial ports got problem. My question is, are there any ways to justify whet...
Hello everyone!!!We have Cisco 3640 RAS server for Remote users . We want to implement a policy that accounts (RAS user Id ) should be locked or disabled after if the user tries with Wrong password . I could say after 3 attempts of wrong password , ...
hello,is what ciscoworks2000 can go up the alarms by e-mail ? exp :if somebody reach by telnet I want a alarm to send by mall has the administrator . thank you for your colaboration.
I've currently got a tac case open regarding this issue and decided the forum may be an idea. Basically the config is fairly simple. I have 6 vlans being routed on the 4006L3 in the preferred "trunked" config between the switch level and the L3 lev...
Anyone seen a switch being unable to set a vtp mode for longer than a few seconds, the switch keeps resetting itself to Transparent mode after a few seconds? All vtp domain settings seem fine though. Switch has already crashed at least once.thanks
I have got 17 Catalyst switches 5500 CatOS 5.5(9) in the network. They all have two connections to two core switches. However, port 1/2 is alway blocking at the leaf end for all VLANs. One of the core switches is the root for all VLANs.I started mon...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-01-2025 08:24 AM | ||
07-22-2025 10:30 AM | ||
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM | ||
11-14-2024 09:33 AM |