Routers - Small Business

Hey!I'm using a RV180W with two WLAN SSIDs set up, one in VLAN1 with access to the whole network and one in VLAN2 with access to the internet only. I need to extend the range of my wireless signal. Can you point me to an AccessPoint of a Router (pref...

I've created two vlans and enabled inter-vlan routing on both. I can access the WAN from each vlan, but I can't access any device across the vlans. Is there something else I need to do?

                   Not sure where to start here.I have a new RV-042 at a new remote site. We have set up a site to site VPN with a Sonicwall device over an ADSL link.50Mb down /5Mb up.All seemed okay, PC data passes and internal Voip seems to work wi...

Hello,Problem sumary: I've recently bought an RV042 router and I can't get the port forwarding feature to work on it, can anyone help me?Details:Years ago I setup a small Linux box to act as a dual WAN router. Recently this box run into HW issues and...

Does anyone know what mib to use for the rv180 router? It doesnt run IOS, it's some kind of linux variant. I used a gerneric snmp host mib but it doesnt quite work. I need interface stats, cpu, mem all the usual stuff. Any assistance would be apprici...

Hello,Wonder if someone might be able to help!I've got a RV180 and so far it is working very well. I have set the logging up and passing the logs to my syslog server. However I'm getting a constant stream of "Warnings" like the sample below:-Tue Jul ...

Hey hi.I have 10 SPA525G phones with me for which I have bought a CISCO 2911 ISR, But after configuring it up, the router says it does not support old model phones such as the 525G.Any idea on how to install. Please help I see discussion where people...

hi, i need know if the RV320 accept two or more IP for one WAN Port, in other words, i need configure this:WAN1 --> IP xxx.xxx.xxx in Vlan 120 (Internet connection)WAN1 --> IP xxx.xxx.xxx in Vlan 20 (VPN Connection)WAN2 --> IP xxx.xxx.xxx (Internet F...

     I have an RV082 hardware version V03 that has been in service for about a year.   I tried to update the firmware to 4.2.2.08 from 4.1.1.01.  All appeared to be going well, then the browser timed out.  I waited a while (10 + minutes) and powered ...

Our environment is connected with 2 MPLS and been communicated with one remote locations . The issue whenever one of our  MPLS is down , another link in our location also not able to reach from our local site vis core switch . But some how the remote...

       We have 2 router which having same IOS and same configuration . There isn't any dynamic protocol is configured ,  how to make one router as active and another as standby

I have a RV042 v.1.3.12.19-tm in the office and we upgraded our bandwidth to 80mbps, however it's only testing close to 20 at best. When I plug it in directly to modem and run the test we're getting close to 90mbps. I've even tested off during closin...

I bought two RV042G routers manufactured 07-2012. One works fine, the second loses VPN connection and access to the web interface in a few minutes after power up (internal network continues to operate normally and have access to the Internet). Both h...

I have to RV320's configured in a site to site VPN between my offfice and my home office. I can ping and access netowrk resources via IP, but hostnames aren't working. Can you point me in a direction that may help get that working correctly?Thanks!

I have just installed an RV042G router. I have one subnet listed as the primary at 172.31.255.0/24.I have a second subnet on 172.16.0.0/16.I have One-to-One NAT set up for two computers on the first primary subnet.I am trying to set up One-to-One NAT...