HI guys, I am setup a VPN with another site, the VPN is working but we have problem to connect the pcs through this VPN. My local network is 192.168.0.0/24 and the local group of the VPN is 172.29.0.13/32. The question is how can I connect the PCS th...
Forum Posts
VPNHi everyone, and sorry for my poor English :) .We try to connect our office to an IPSec vpn, but we encounter some issues with that. Phase 1 and Phase 2 seems to be OK, the tunnel looks UP, but there is no traffic nor ping between the remote ip ho...
Hello Experts, @Richard Burts @Peter Paluch @Joseph W. Doherty @Julio E. Moisa @paul driver I have question, We have four sites connected with each other through MPLS circuit. We are advertising our subnets by using ospf and I want to use DMVPN a...
Hi, Newly configured ASA 5585-x with BGP interface, how does one route all traffic to another interface with the advertised public IP's? Or does one create VLAN on same BGP interface? Many thanks in advance for your kind assistance. CheersGeoff
Resolved! How to display all ISIS routes
Can anyone provide the command that will show all routes learned for a specific network? This is not just the installed routes, but all other routes as well. Any help would be appreciated.
Resolved! EIGRP through tunnels
Hi There, Thanks for reading. I have WAN routers which ping each other, have tunnels up / up (those IPs ping) and can ssh from one to the other. My problem is tunnels are not allowing an EIGRP neighborship to form. No auto-summary is included i...
We upgraded from a 3925 to ISR4451 running Version 15.4(3)S4. Most of the configuration was copied over from the old router to the new one with some modifications as it is a much newer Device.GigEth 0/0/0 is connected to the DataCenter uplinkGigEth 0...
Resolved! VPN Site to Site
Hello I'm struggling on a site to site vpn with a third partner, i don't have access to the remote end. The State is MM_KEY_EXCH and i already double check to the PSK with my partner. Can you help me figure it out : Thanks ######################## Co...
Resolved! HWIC 2T Cisco Router 1905K9
Hello!I own a Cisco Router 1905K9 and it is not recognizing the "HWIC 2T" The version of my IOS was "c1900-universalk9-mz.SPA.150-1.M8.bin"I upgraded to the "c1900-universalk9-mz.SPA.157-3.M.bin" Attached files are attached with the output of the com...
Resolved! OSPF - limit neighbors questions
What options are there to limit which routers OSPF neighbors form with? I am aware of limiting interfaces (via "Passive-Interface") that participate in OSPF advertisements, but I was wondering if there were other / more efficient options ---> especia...
I replaced 5 point to point T1s with a single Metro Ethernet WAN which has five endpoints and I use OSPF.I'd like to understand the best way to limit unnecessary neighbor adjacencies between my routers. Most sites only need to see one or two other si...
im looking at the config of a cisco 871 the bridge interface looks to my lan interface. how do i check which physical ports are part of the virtual bridge interface ? #sh ip int brInterface IP-Address OK? Method Status ProtocolBVI1 10.1.6.1 YES ...
I am having some difficulties where to even start with this but my need is for anyone on the GE1/3 to communicate with GE1/6 back and forth.My reasoning for this is my GE 1/3 is a Wifi Router which simply leads to the internet and works for normal da...
Can some Body, tell How To Add, Modify, and Remove VLANs on a SG350 Using SNMP.I can do it on SG 300 but my Programm doesn't work on SG350.What' s new on SG350thx
Hello, I'm new to QoS but I read through blogs and Cisco documents and have a config I've put together but the interface is not accepting the service-policy. I need to configure QoS on a 10 Mbps line so that voice/video traffic is given highest prio...
